Search results

  1. U

    Parts 1UZFE cometic gaskets, ARP studs, starter, alternator, manifolds, mounts

    Im moving and prefer to sell stuff rather than pack it up - let me know what you want/need * Pair of new, still in original packaging, 0.051" cometic MLS head haskets ($180 on this site) -> $125 * New in box ARP head stud kit ($360 on this site) -> $300 * Starter -> excellent condition -> make...
  2. U

    "Coil on plug" coils for 1UZFE

    Unless everyong already has AEM boxes that need converting, why bother trying to fix something that doesnt work when there are plenty of options that do work straight out? AEM, in my opinion, is nothing particular special. If it doesnt work, or is not flexible enough to run a simple COP v8...
  3. U

    Oil Jets

    There are many ways to fasten these other than threads. Clearance is the question that is causing me pause.
  4. U

    Oil Jets

    David, How thick is the block before you hit the oil galley? It looks pretty thin (eg no room for drill-tap). This may end up being a pan-head rivot project. Have you had a chance to check crank clearance yet?
  5. U

    "Coil on plug" coils for 1UZFE

    Depends on the box you are using
  6. U

    Oil Jets

    Cribbj, Thank you for the diagram. It appears that the depiction calls for four oil jets per piston... "Four oil jets for each piston are added" Is this just a english-translation issue or are 32 jets really needed. I am assuming the first... just thought I would ask the obvious for the...
  7. U

    "Coil on plug" coils for 1UZFE

    If your box is using ground to complete the circuit for spark (like every other EMS I have seen/used), then you will need to run a relay to switch the coil from 5v to 0V. The EMS will control the relay which controls the 5v switchable. The problem is that standard relays will never react fast...
  8. U

    "Coil on plug" coils for 1UZFE

    Rod, Cheers for the photos of the ford COPs. From the photos, it looks like the ford COPs have a good 10-15 degree bend in them. Is this joint flexible, does it straighten in the spark plug tunnel? I am assuming not since you mentioned the need for an extension yet the coil is sticking a...
  9. U

    Head Gaskets

    rpm gaskets Zuffen, Just a heads up... the gaskets being sold at the link that you listed (rpm machine) are not MLS they are composite (CFM). I cannot find another source for MLS beyond this site. Anyone find another source for MLS?
  10. U

    Fidanza flywheel interest

    Hiluxmad, Look under the group buy section. There has been a long discussion about this flywheels conception. Shipping to AU should be about $35 USD.
  11. U

    CNC possibilities

    What about a transmission adaptor plate for the 1uz that was universal... It would have the proper outside perimeter cut (including the bit for the starter), dowl holes, and bolts holes. It would also have the inner perimeter cut into a circle for flywheel clearance. The only thing the...
  12. U

    Fidanza flywheel interest

    Fidanza is offering between $325 and $375 (USD) for 1uz aluminum flywheels with replaceable steel inserts. However, we need to give them a good 10 wheel order before they will begin production. Who's interested?
  13. U

    pilot bearing

    Thanks sprinterTRD, I will be using a porsche 951 geabbox that uses a seperated clutch/bellhousing assemble from the tranny. The OD of the spline is .575" (14.6mm); also the ID of the pilot bearing... So, sounds like I need to part out a 14.6mm ID, 40mm OD pilot bearing... thanks
  14. U

    Fidanza flywheel interest

    If you dont mind me asking, what kind of $$$ do they want for it.
  15. U

    pilot bearing

    Does anybody have the OD for a 1uz pilot bearing. The crank is behind the mounting plate on my engine stand and I just assume leave it on the stand unless nobody has the number available. thanks in advance
  16. U

    Fidanza flywheel interest

    SCV8, Do you mean that the 3L turbo diesel flywheel will fit the 1uz crank bolt pattern and has the proper ring gear size (that would be a great find!), or that the clutch will fit? If it is the later, what does the clutch fit? From my understanding, most on this board either use of the au...
  17. U

    exhaust manifold flanges

    Thank you kryan, How have I missed this page??? I thought I had seen all the au suppliers. thanks again, great resource
  18. U

    Fidanza flywheel interest

    I have begun the long road down the "which flywheel/clutch combination" path. I am using a custom iron clutch and custom pressure plate. I really want to stick with an aluminum flywheel (dellow and castlemans are out) and, obviously, a steel insert... fidanza style I have been in...
  19. U

    exhaust manifold flanges

    I have just finished the looooooong archive search for header flanges. I appreciate all the work that has gone into header design and development. Unfortunately, I will need to make my own headers for this swap. I noticed that many folks are using mild steel flanges that look very similar to...
  20. U

    dellow flywheel

    Peewee, I appreciate your advice, and, agreed, a launched flywheel is certainly not safety approved. Why do you feel that a welded/redrilled flywheel is weaker than a fresh milled wheel? It seems like, if the welds and resurfacing are done properly, that the difference should not be...


Top