Parts 1uzfe Forge Internals and other parts!!!

[sunami02]

I've decided not to pursue my 1UZ build, there other matters need my attention / Money.
Parts are All brand new, most are still in original box. Best offers are accepted. if someone buys all I'll donate a 1uz complete short-block, intended for the build.

Items are located in ATLANTA, GA

Mods- I have my vouch.!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! PICS ON LINK BELOW!!!!!!!!!!!!!!

ARP - FLYWHEEL BOLT........... $70

Custom Made - Crank Pulley............pending


New Stock Regrind Cams by (Crower) include valves lash spacers( Crower)........$800


Quantum auto aluminum flywheel installed but new........... $500


1uz to w58 Adapter plate ( Aluminum ) $160

SPEC - clutch 6 puck( works with the Quantum auto flywheel W58 set up)............... $300

ROSS RACING Forge Piston - 9.5 1, STD bore, made to order. BRAND NEW ( ring, pins, and lock pins are all included) save wait time.......SOLD
Metal head gaskets along with other gasket included new......SOLD
Crower- Valves springs & retainers Brand New (32)......... Sold
ACL - race rod bearings complete.............SOLD
ACL - main bearings complete ..............SOLD
ARP - Head studs Brand new .......... SOLD
Water pump new..........$SOLD
Timing belt , new idler bearing. . .. . .. . .. . ...$SOLD
TTC - Forge I-Beams rods with ARP 2000 rod bolts New........$SOLD
TTC - High flow Aluminum fuel rails Brand New (2) .............$SOLD

http://s29.photobucket.com/user/sunami02/slideshow/1UZFE parts

 

[cribbj]

You've got a bunch of good stuff there - GLWS.

Could you get a better photo of the cam card? The actual cam specs are hard to read.

 

[sunami02]

You've got a bunch of good stuff there - GLWS.

Could you get a better photo of the cam card? The actual cam specs are hard to read.

ZOOM In on the picture!!! you should be able to see it. on the pic bottom right button.

Thanks!!

 

[sunami02]

Hmmm there seems too be alot of supra guys with 1uz?

I hope that most parts will go to just one person. it would be just incomplete. with one here and there.

Your breaking down your engine to built!! SO BUILT IT RIGHT!!!

 

[BoostedV8]

Damn!!!! Wish I could get all the motor stuff!

 

[sunami02]

You can!!!!!

I just up here in GA man!!!! its close!!!!

 

[kc95sc400]

whats the word on the valve springs compared to stock. Not fluent in valve spring specs so dumb it down for me some.

Thanks.

 

[sunami02]

whats the word on the valve springs compared to stock. Not fluent in valve spring specs so dumb it down for me some.

Thanks.

They are New and Stronger then the stock ones. handle more abuse. Pretty much sums it up

 

[kc95sc400]

They are New and Stronger then the stock ones. handle more abuse. Pretty much sums it up

Very tempting, cams too.

Are the cams boost friendly?

 

[sunami02]

Very tempting, cams too.

Are the cams boost friendly?

Yup, cams where regrind to the spec boosting. But its OEM cams.

 

[Alan Whitaker]

Hi
PM sent

Alan

 

[stevieg]

Yay, forged internals on the way and the quest for 1000whp begins lol

 

[sunami02]

Yay, forged internals on the way and the quest for 1000whp begins lol

Do your updates!!!

Keep me posted.

 

[sunami02]

Things are Moving!!!! thanks Lextreme!!!!and everyone!!

 

[stevieg]

in case the OP ever returns I had a few issues:
1. the STD bore ross pistons were actually 0.020" over bore
2. the ARP2000 bolts were actually knock-off 8740's
3. the waterpump, timing belt, gaskets and MLS head gaskets were all POS Chinese knock offs and I ended up replacing when they shit the bed
4. the ARP head studs were the wrong ones (fine thread on both ends so I assume 2uz)
5. the crower cams were packaged so poorly that two of the cam lobes were chipped

there was other stuff too but its late and I can't remember

 

[Mikedp86]

Do you still have the 1uz to W58 adapter?