Search results

Hi all, I'm hoping someone on here might be able to help locate my car that was stolen form Tullamarine last night. The vehicle was a 1981 short wheel base beige FJ40. Had a 4.0L Lexus V8 & 60 series 5 speed, power steering, front & rear air lockers, all engineered. The vehicle is fairly...

Hi all, I have had a 1uz in my 40 series for about 2 years now and am almost on my second clutch. First one the center tore out of it and today the fingers on the pressure plate broke. I used the CRS kit and have had nothing but trouble with it from day one so I am looking at going auto. What I...

Okay so here's my problem... 1UZ alternator light came on a few weeks back and at the same time smelt some smoke under the bonnet. Power steering pump had a slight leak so i thought that had gotten into the alt and killed it. So i rebuilt the pump and took the alt to be bench tested at the auto...

Looking for a 1uz power steering pump in good condition in melbourne, or that can be shipped to melbourne. If you can help out send an email to [email protected] Cheers, Adam.

Does anyone know how to test if a coil is stuffed or not? I have done the procedures outlined in the pics below and i am getting 0.9 ohms on the primary coil when it should be 0.41 - 0.50 ohms. Does this mean my coils are stuffed? I get the same reading on both of them. The secondary coils are...

Does anyone have a set of coils to suit a 92 LS400 in melbourne? Please contact me via email: [email protected] or on 0421 361 523 Cheers, Adam.

As above, i need a set for a 92 LS400 in Melbourne, Australia. I have a set here i can swap if need be. Don't know what they're off, but the code on them is '123'. Email me at [email protected]

I have a 1uz which is from a 92 LS400 and am almost finished the conversion into my 4x4. Just noticed that the plugs in the loom for the ignitors look different to the plug on the ignitor body & won't fit together correctly. Or are they just a really tight fit? Do these differ from year to year...

G'day looking for a small fuel surge tank, in melbourne. Adam. 0421 36 15 23 [email protected]

Hi guys, I am in the process of wiring up my motor using this diagram http://www.lextreme.com/forums/attachment.php?attachmentid=2527&d=1135948925 One thing that has me stumped is, on the side of the motor there is a large wire that goes to the starter motor (see pic). I am assuming this is the...

This is the setup I am planning on using for my motor swap (40 sereis 2F > EFI Lexus 1UZ V8 ). Can anyone see any problems with this? Will i need a low pressure lift pump between the tank and the filter?

G'day, i hope this makes sense to everyone, I'm putting a 1uz into a 40 series landcruiser and originally the radiator had an overflow bottle ( i think thats what its called) with a small plastic cap on it and the radiator had the cap you have to push down and turn to seal. My question is what...

Does anyone in oz have an old wiring loom they want to get rid of? I am just after the connector that goes to the passenger side coil and to the oil level sensor. Cheers, Adam.

Have done a seach but cannot find the info i'm looking for. From what i have found (correct me if i'm wrong) the early 1uz's had bilet steel fuel rails and a cold start injector while the later models had cast fuel rails and no cold start injector. Now the motor i have has bilet steel rails and...

As above, i am after a rear sump and oil pick up to suit 1uz. I also have a front sump and pick up i can swap if need be. I'm in melbourne. Adam

As above - remote oil filter setup to suit 1uz, i'm in melbourne. Cheers, Adam

Hi all, can anyone recommend someone in melbourne with experience in wiring up a 1uz with the stock ECU. This is to go into an 81 toyota landcruiser. Preferably someone mobile who can come to the car...

After a powersteering pump for a 1uz ls400 in melbourne australia. Cheers, Adam.

Hi everyone, this is my first post on the forum, but have been reading for quite a while - geat site! Well my 1UZ for arrived today to go into my 40 series landcruiser, just trying to id a few things on the motor so i can start on sorting out this conversion. Any help or hints anyone can offer...