Search results

Hey guys flipping the intake manifold, do the fuel rails also have to flip with the manifold? I gave it a quick shot but the fuel regulator got in the way. I do know that a longer accelerator cable, hoses etc for iac etc will be needed. Just wondering if the rails also have to be...

Hey guys, I have always had my power steering control valve just recirculating into itself since i had done the conversion in an effort to control the idle. Since then i have been running an after market ecu and idle is perfect. Issue is that when i turn full lock the idle drops causing...

Hey guys, i have a a sealed stepper motor and was wondering whether it can be opened, serviced and then siliconed closed again? I have tried carby cleaner but it hasnt made a difference. I know they are really hard to find and i believe that the wiring is also different. cheers

Hey guys, currently doing the valve stem seals and timing belt on the motor and i thought it would be a good time to remove the egr. now looking at the exploded drawing on the website, there are a few things that i cant find. 1. egr vsv - i can see a pipe that runs to a pipe under the...

Hey guys so i have pull the front end of the truck apart to change fan belt and some general tidy ups as its been sitting under a tree for the last few months and noticed that the oil cooler was setup in a way i wasnt familiar with. opened the connections and it was still brand new inside...

hey guys, i've got error codes 41 & 47. I have swapped tps's and checked wiring and all seem fine. So what i gathering is that its an ecu problem. This has now led into a different issue, tracking down another ecu... so my question... are ecu's compatible between motors? my current ecu...

Hey guys ive noticed that when i do a water crossing of substantial water (yesterday melbourne had really bad floods and issue arose again) the engine starts running of less cylinders. Now this only happens the first time i hit water and after maybe 5mins everything is fine and i can drive...

i have been going through alot of posts on idle and afm issues... i originally had big missing issues... rig would accelerate without missing massively. I unplugged the afm and it was running fine, rich, but fine. i am currently on my 2nd afm and the rig has started to miss again... (was...

if installing cams (for eg the lextreme stage II), what other supporting mods would be needed... like oversized valves, springs port and polish? would an aftermarket ecu be needed? thanks daz

my car idles at around 1.5 and sometimes 2k. then when coming to a stop it will start hunting for a couple of secs and then rest at around the 1.5 - 2k mark. It was running fine up until a week ago... and nothing was changed. Is there a way of adjusting the idle or checking the ISC...

the car runs fine sometimes... and then sometimes misses heavily when foot is full down. Mainly in the mid range... i have checked the leads and the ohms are off the charts... i have ordered a new set and they should be in tonight. i will change them straight away. i have checked the error...

Intake air temp sensor Hey guys, i just did a diagnostics on it and got this code. I did a search but couldnt find anything. What would i be looking for to try and correct this? thanks daz

on the dash, only the battery light is on, the fuel pump or nothing turns on. it wont turnover. the battery was dead and it was swapped with another, there then was a short and this happened? Anyone have an idea of what it could be?

i was wondering where the water temp sender is? thanks

i have just installed a 1uz into a toyota surf. the switches on fine but the idle is not constant. As in, it just goes up and down, up and down... not like its missing, just up and down in sequence. When i rev it or go to drive it...it will only rev to around 2 -2.5rpm and then it starts to...

i need a pinout diagram for the power plug side of the ecu as the the plug was cut. i have checked the diagrams on this site and its not what im after... or maybe have missed. does anyone have one? model numbers are as follows: A9661-50171 175000-7150

what would be the going price on a new starter for the 1uz. Australian dollars if anyone knows thanks daz