Recent content by 400ZED

  1. 4

    Cars For Sale Dato 260Z running 1uz for sale

    It may be off the market already. Crazy coincidence? If so I know I have not been on the forum much since I built this car but I owe a lot to all of you guys for helping me build it.
  2. 4

    Cars For Sale Dato 260Z running 1uz for sale

    It has happened I am married and don't have time to give my Dato the time she deserves. So it is up for sale hopefully someone else can treat her the way she deserves. Summary Car 1976 Datsun 260z 2+2 recent low king springs and new munroe's 16" superlights brake upgrade: Front 260mm...
  3. 4

    Wanted Viscous fan (Pulley only)

    Does anyone have a Fulley of the back of a crown Viscous fan?? I have had my car off the road for ages and i do mean ages. one of the few things i need is a Viscous Thermo fan Pulley. I am changing from Hydralic fan - Electric Thermo and i am using the Crown housing as a idler for the fan...
  4. 4

    Removing headers

    that is what the dots are for. i have always used them i think there is a set of one dots and a set of 2 dots 180"opposite. really odd that the other side did not line up. i would be very dubious about putting them back in a way they did not come out. did you put a little bolt in to hold the...
  5. 4

    overheating gremlin

    has any one had experience with electric water pump from davis craig. they flow 110l /min and have a temperature controlled variable flow. they just plumb into the radiator hose i think. I was a bit worried about quick warm up as you won't have continous flow through the motor unless it was...
  6. 4

    overheating gremlin

    heater is disconnected but i did blead the system thriough it cheers. Acl just got back to me with the codes on the current production run i am yet to read what mine say. cheers guys
  7. 4

    overheating gremlin

    Cheers RMS is the difference much. do you think it could be giving me the problem i have? Does anyone have a set of ACL head gaskets that they can tell me what is on the tabs of the left and right one??? there is a tab that pokes out from between head gasket and block. i will look at it...
  8. 4

    overheating gremlin

    the water flows the right way i was curious about that. when running the top of the radiator is hot to touch the bottom is cold. as the thermostat picks up water from the bottom of the radiator could it be too cool and always closing. i doubt it caus when i pulled the thermostat out just after...
  9. 4

    overheating gremlin

    Hi guys it has been a couple years since i have posted but now i need help. I replaced the engine and put in new cams NA car and it never ran very cool bit of a head gasket leak eventually it got bad and i gave it new ACL head gaskets and skimmed the heads. since then it has useda a lot of...
  10. 4

    How much flow needed thru cats

    i was running 6 pound bcak pressure before my cats and i could not find anyone to tell me how much i was meant to have i removed the cats and got down to 2 pound. with maybe some smal horse power increase, but some other things changed at the same time. measurements were taken at 5-6000 prm...
  11. 4

    bent cam locating pin

    I have not been able to watch it with the lap top attached. so i can't datalog anything. bummer. it will seeming ly happen when ever it wants. what ever gear whatever load. my other thought over night wasthat it could be a drive line snag like it is grabbing 2 gears at once. I am lost i...
  12. 4

    bent cam locating pin

    I wish it was simple It only misses once - twice a month. if it misses at idle it stops instantly. this thing has lived on a dyno that thing i have done something like 60 power runs during three full tunes and a couple of clean ups. I am running wolf. it runs like a dream 99.9% of the time...
  13. 4

    bent cam locating pin

    Zuffen i have thought of that it would not be nice removing it later. OZ the bearing s are fine you are right the pin is only a locater. Would a second locating pin help transfer much load? The vehicle has a very ocasional miss. it happened with both motors so it is a wiring/ computer/...
  14. 4

    The buy of the Year!

    what do you want with 4 rx7 injectors? are you going to Stud your block or did you buy a set of head studs? it would be nice to have the piece of mind to have a fully rebuilt motor.
  15. 4

    bent cam locating pin

    I did not edit that post you may have just read it better. The cam pulley is Located by a pin it is not a drive pin it is only there to locate. My new cams fit fine Just like OEM. There is no Keyway. The Cam pulley is a friction drive that is why the Torque Spec for that Bolt is so Darn...


Top