Search results

Very nice install, Steve. Everything looks like it came from the factory. I'm looking forward to the performance numbers. Just curious, what is the hotside a/r for the turbo?

The only real Q45 is the 90-96 G50 chassis, IMO. The later years were just rebadged Nissan Cimas but my views are a bit biased. I have a 94 that is turbocharged and a 95 that is mostly stock. The engines are relatively trouble-free and will last for a long time if properly maintained. My...

Your project looks awesome. How fast do you reckon the car will be at the dragstrip?

I'm running a BEGI FMU on my Turbo Q45. It worked out great with the blow-thru MAF setup. It's adjustable so you can play around with it and get a nice a/f ratio under boost. My stock injectors are 370cc so all I needed was just a bit of extra fuel under full throttle which the FMU helped out...

Some more pics: THE VH45DE HAS PISTON OIL SPRAYERS BUILT INTO THE CONNECTING RODS. YOU CAN SEE THE OIL SPRAYER HOLE IN THIS PIC.

The VH is definitely bigger than the 1UZ which makes it kinda hard to use for a lot of swaps. As far as weight, it is over 500 lbs with all accessories. The block is aluminum but all the cross bracing makes it heavy. I think it is a perfect candidate for boost applications. Change out the rods...

The VH45 is rated at 278 by Nissan but the actual output is more. Most estimates are somewhere closer to 300. The reason for Nissan claiming a lower hp was the "Gentleman's Agreement" between the Japanese auto manufacturers and the Japanese government which placed a 280 hp limit on engines.

I'm running 6 psi on my engine without any problems. It's putting out somewhere around 420 hp. One of the guys on my site is running 8 psi on his Q45 and again no problems. The only reason for failure of the VH45DE at 350-400 whp would be bad tuning or a defect in the engine.

...................

I found some posts on the internet where someone says the VH45 has a weak bottom end but I can't see why they would think so. The engine has 6 bolt mains, plus a ladder frame that ties in all the bearing caps. The crank is a non-twist forged unit with plenty of overlap and the rods are also...

This was a spare engine that I bought a while back. There really wasn't anything wrong with it other than the fact the oil wasn't changed like it should have been. I didn't have a place to store it anymore so I decided to just disassemble it.

Hey guys. I thought you would find this topic interesting. I disassembled my spare VH45DE engine and took a bunch of pics. I know that we've talked about the strengths and weaknesses of the VH on this forum before. Here's the link for the full write-up with photos...

Here's a vid that I did today. The weather was dry. I brake torqued before I launched but all I got was wheelspin. Oh well..... it wasn't the best run but I don't think it's too bad for only 6 psi. http://www.youtube.com/watch?v=3_Kz9fgQyzw I'm going to be replacing the wastegate spring...

The trans has been rebuilt by Level Ten so it shifts faster. I'd say it is worth about .3 seconds per shift. I saw that video before. The power is crazy. I don't know how much boost that thing is running but it is definitely screaming. Last I heard, they had upgraded the internals and were...

Hey guys. I wasn't able to do much on this project for almost 6 mos. I finally got back to the car and started finishing off the last bits. When I left, I had the car running but didn't tune. So this week I hooked up the wideband O2 sensor and started to check the a/f ratios. I fiddled...

I figured this out when I built my turbo system. I'm running all 8 cylinders into a 2 inch OD pipe that goes for 8 feet before it feeds the turbo. The car pulls hard all the way to 6900 rpm. Of course, I'm running a measly 6 psi for the moment so there might be some issues as I raise the...

The Z32 300zx coilovers will drop the car an easy 2.5 inches all around. The Eibach springs that I have on my car take it down by 1.5 inches. As far as brakes, you can put the Z32 and Skyline GTR brakes on the Q. My car has the front brake setup from the R32 GTR. Like I said, the rear wheel...

Actually, I'm running Eibach springs with Tokico struts. To my knowledge, there are no coil-over kits available in the States. You might get some from Japan. Some people have installed the Z32 300zx coilovers on the Q with slight modifications but the car will sit very low. The Q, Z32 300zx...