Search results

So i've been narrowing down all my parts and I have most of them now. I'm working on the clutch and pressure plate setup to go along with the 1UZ and the R150F for my 4runner. There are a couple people using the Marlin HD clutch kit for the 3.0 and there's also another guy using this one...

The R151F is out of a the 22RET (turbo). I'm looking for info on the R150/F and the KSracing bell housing. Thanks.

From what I understand the R150F is from the 4wd trucks and the R150 (no "F") is from the 2wd trucks. Commonly people refer to them both as the R150 so reading about them can get confusing. I know there are input shaft length differences between the R150F that bolts to the 3.0 (3vz series motor)...

What is the cable/loom that runs right by the furthest forward most O2 sensor on the driver's side. The clip for that O2 sensor is connected to one of the loom/wire/cable holders on the block. It appears to be the starter cable, but am unsure because I can't see the start :mad: I'm pulling the...

I have a 1991 LS400 that I'm parting out. The interior and electronics are in great condition. It is gray interior and even has the original phone inside! The list below is not everything, but a simple generic list that I have added. There is nearly every single interior/exterior piece on...

ha ha ha. I've been over here for quite some time. While I looked at many different options and new of a few things needed for each, I had originally done all my research on the 1UZ so I do know quite a bit about it. I have a ton of info "thrown" into this thread for more my purposes than...

The same as what?

Thanks for the info. I know I would thoroughly enjoy the 1UZ. From what I have read, it is one HELL of a motor.

Well that is good to hear. What size tires and what gearset are you running in the diffs? I have been searching for a 92-94 sc400 for the swap for a couple months now. Just waiting for one to come along. My goal is 20mpg all around (excluding towing or offroad use). Do you think this is...

It seems somewhat unrealistic then. Considering that seems to be about a 2400 lb car (roughly). On another note, how do you like the swap? Edit: anyone that has swapped them into a toyota truck? List some specs. Also did you account for all the gear/tire changes etc...

Is Is 20mpg or 14.1 Liters/kms out of the question for a 1984 toyota 4runner mixed driving? This excludes offroad or towing. I would like to get the early 1UZ Truck ------ 1984 Toyota 4runner 5.29 Gearset (can change) ARBs front/rear Front Rear Tube Bumpers Currently Running 37x14.5's...

Thanks for the input that was the kind of advice I have been looking for on the adaption.

I have seen a few kits out there for bell housings, flywheel and clutch setups out there for the 1UZ to R150 adaptions, however I am curious to hear from those that have done the swap before (going into an 84 4runner) what is the best way/kit to go with?

what about the sc400, I didn't see any mention of it. I believe they started making that model in 91. I would assume, since it is prior to 94, then it would have the early model gen I motor in it as well correct?

I have looked and looked and looked on any specific information as to the "Gen I" years of the 1UZ. Looking for the stronger 1UZ engine. Does anyone know this information for sure? I will be purchasing a donor vehicle based on getting the stronger 1UZ engine.

could anyone shoot me over that document or let me know where I can view it? [email protected] Thanks.

Great, I appreciate the help and I will be ordering some items from you once I have finished up the research on everything. Would you recommend picking up one from an an SC400? or a different model? From what I've read so far, it seems the SC400 would be easiest in the trucks. You would know...

My current setup is high cross-over steer from Trail-gear with the lift kit as well. The front axle has been moved forward about 1" with the kit. I am running 1" BL to simply make working on several things much easier. I want to link the front and rear in the future (after the swap) and drop...

I am a little confused with this information from your site. Do you mean a rear sump for solid axle setups? "We have mounts to suit from 1980 through to 2004 Vehicles. We have sold over two hundred of our mounts with many happy customers We recommend front sump for solid axle vehicles and...

I have seen a few kits out there, I just wasn't sure if there was a flywheel from another vehicle that was a bolt on. gloverman: have you updated your manual for electronics yet?