1uz

Alright, its hard in my area to find a good shape sn95, im 16 and want something to take to crusin the coast and drive to school but really want the reliable toyota v8 but im a true mustang fan, i really need help from the experience swap guys to figure out how everything will work, wiring...

hey there I’ve been trying to find someone that would sell me a carby manifold and distributor setup for 1uz , new , second hand , whatever , haven’t had any success with csl or harcourt the latter s phone number is disconnected, I’m in aus the setup is for a surflifesaving boat so extreme...

Hi 1. I have swapped in a 1uzfe v8 into my mitsubishi van. At the moment it is not performing at 100%, I feel some type of hesitation when trying do fast accelerations. How much can a faulty Airflow meter affect the engine's perfomance and what octane fuel can you suggest to be best? I run a 5...

Hello all, I need help here. I own a 1990 ls400. Planning on making a mean sleeper out of it. I can make just about every part under the hood from scratch, but I have no idea where to start as far as the wrenching side if things go. So here we go guys. A little patience will go a long way...

Long time fan, first time post. I currently have a 04 4runner and 09 GX. Love the engines, I also have a 1990 Plymouth Grand Voyager with a 3.3L V6. I found a Mopar guy down in Delaware to work on the engine and transmission, however that fell through. Project has been delayed essentially...

Hi! To make a long story short: I have a Nissan 200SX S13 drift/track car, with an 1UZ-FE VVTi swap. Custom harness from PEM in England(stock ECU), double 12" electric fans and a 58mm aluminium radiator. Filled the radiator with red coolant, and let the car idle for about 10 minutes, and the...

Hi all, Friends and I have a VVTI 1UZ from a 1998 LS400 swapped into a Mk2 Celica. We went through the wiring and paired off what we didn't need, hooked up what we think we did and are able to start the engine ok, its able to idle happily. Trouble is the e-throttle doesn't respond to the...

Hey everyone i have recently dropped a 1uz into a 93 surf. I purchased a microtech ecu off a friend and all the maps have been messed with. Any chance someone has a base map for microtech lt-10 or has photos of their map setups? Cheers

So ive got a 92 sc400 and a while back i was driving and it sounded like it was running on seven cylinders then it died on me, it would start for a second but die immediately. When i popped the hood there was oil and coolant all over the place, had it towed home and upon further inspection there...

1uz adapter kit: https://www.dropbox.com/sh/x45axnzemhcymyx/AABp1EHnjni2k0FkvBkLKjEka?dl=0

Blew three half dollar sized holes in mine doing donuts when something inside let go. Yet to find out, zip is 11206, Brooklyn NY.

Hello, I have a 1996 OBD2 1UZ in a Nissan 240sx. Ive got the thing up and running and id like to pull the codes. I cant seem to find any information about pulling codes on an OBD2 without using a scan tool. Is there a way to do this without a scan tool? So Far i have tried grounding the T1...

Hi There guys, I was wondering if I could get some insight and pro knowledge on my newly started project I've just started rebuilding the rr classic 3 door for hunting, with the engine of choice being the famous 1uz vvti. I'm new to the 1uz family but have a friend helping me with the build...

This offer is a device that eliminates limp home mode, which is otherwise active if ECU does not 'see' stock auto transmission. Earlier ECU models (1UZ non-vvt, 1jz, 2jz before 1998) didn't have "underpowered" fuel/spark/vvti (for the JZ) maps for N/P transmission range, so these ECUs are...

Hi guys I'm having a lot of trouble locating a diagram for my ECU, its a 89661-50170 (34-22-16-28 layout) from a UCF 1X Celsior. http://www.toyodiy.com/parts/xref?s=89661-50170&mJ=on&mG=on The loom had been wired for a later (UCF2X) ecu that didn't match the motor and I am now just trying to...

Running 1UZ vvti off '98 celsior, ~60k' s on it. Timing stuff replaced (belt and everything), water pump also replaced with toyota original unit just incase. Old WP was fine though. Radiator is brand new aluminum aftermarket unit, the biggest one I could fit. Sized about 600x450x60mm. Using...

Just looking for a 95 SC400 1UZ ECU so I can keep my UZ swap going. I know there are more experienced people on here so if other year ECU's will work, let me know, thanks guys.

(i hope im posting to the right spot) hello all, im new to the lexus community, i bought a (1st gen) 1uz with a bunch of extras. i plan on putting it into a 81 toyota pickup, but in the mean time of gathering parts, i came across a 4.7 TRD SC, which i have a chance to get my hands on...

Hey guys, Super new here but have been lurking the forums for a while. I'm currently putting a vvti 1uz into an 87 Fc3s rx7 drift car. Right now we have the JDM VVTI engine, the Collins performance swap parts, and the sr20 trans to make it work. The engine showed up with cut harness and no...

Well as every story has a beginning. So does this one. I have always had a soft spot for Z cars. When I turned 19 I was working at a local auto parts store making barely better than minimum wage. but I still lived at home with the parents. So I decided why not go out and buy an expensive sports...