Will these headders fit a 1UZ??

[Udlman]

They say that these will fit the 4.7L V8 Tundra, which I assume is the 2uz or 3uz. Will they fit a 1uz??


http://cgi.ebay.com/ebaymotors/Toyo...ptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccessories

Thanks, Brad.

 

[Lextreme II]

Yes they will fit the engine but might fit your chasis. Great price.

 

[Smitherz]

WOW that price is too nice. :thinking:

Hmmmm really compact too.

 

[soarer4.0gt]

so whos gonna take one for the team an try them on an sc4? lol

 

[Udlman]

Thanks guys, I will get these and see how they go.

Cheers, Brad.

 

[JBrady]

Guys... these have been tried multiple times. They DO NOT FIT any Lexus car. You could possibly substantially cut and reweld several pipes and the collector but that would be quite an undertaking. These fit the TRUCKS ONLY.

 

[Udlman]

I am doing a conversion on a Surf/4Runner, so should be ok. May have to do some minor mods.

Cheers, Brad

 

[-Nemesis-]

They're the ones that I have, they're all much the same. The primary/s on the drivers side will need remodelling to miss the steering shaft and the passenger side o2 sensor lines up with the torsion bar in mine, so I had to relocate it

It's a bit late, but I was going to warn you that they're cheap, not just in purchase price.

I've been chasing leaks in mine since day dot, they have since cracked in a few places (possible the stress from my rigid exhaust)
The main flanges were bananas and needed machining at extra cost
And being such thin walled they transmit a lot of valvetrain noise.

And I paid a lot more than that, through a certain Aussie 1UZ fab shop in Qld that everyone up there uses :sad2:

 

[Udlman]

Thanks Nemesis, I run a machine shop up here in Bne, so machining and modifications aren't a problem at all. Will see what they look like when they get here.

Cheers, Brad.

 

[Alan Whitaker]

Hi All.
I also was looking at these, my question is will the fit the 1uz, I have plenty of room either side of the engine, will the flanges fit the engine.

Many Thanks

Alan

 

[-Nemesis-]

Yep, they will bolt to a 1UZ

 

[Udlman]

They arrived today and look good, everything looks straight. Tig welding is better than average. But hey for the $$$, it is cheaper that I could have done them for, and they come with all gaskets as well.


Cheers, Brad.

 

[-Nemesis-]

Stick em on a flat bench, will be interesting to see if the flanges are square unlike mine.

 

[Udlman]

I stuck them up against my fishtank glass and they looked nice and flat.

 

[-Nemesis-]

Good stuff then!

 

[zidaro]

How close do they fit to your block-- "block huggers"? Any way you would include a photo?

Thanks, aaron

 

[Udlman]

I can post a photo when I finally get the motor and the pull it out of the halfcut. I have been doing things a bit backwards, buying bits as they come available.

Cheers, Brad.

 

[V8_IS200_marcus]

if they fit, i take this set will fit then, http://cgi.ebay.com/ebaymotors/Parts-Accessories_Car-Truck-Parts-Accessories__Toyota-01-04-02-03-Sequoia-4-7L-V8-Exhaust-Header-NEW_W0QQitemZ220369905712QQddnZPartsQ20Q26Q20AccessoriesQQadiZ2865QQddiZ2811QQadnZCarQ20Q26Q20TruckQ20PartsQ20Q26Q20AccessoriesQQcmdZViewItemQQptZMotors_Car_Truck_Parts_Accessories?hash=item220369905712&_trksid=p4506.c0.m245&_trkparms=72%3A1171%7C65%3A12%7C39%3A1%7C240%3A1318

 

[-Nemesis-]

They look like the same thing, only $100 more.

 

[V8_IS200_marcus]

Hi there, yea i know they cost more, i was just asking if they fit, think i did see some for around the same price as the 1st lot that was posted on here, well im going to get a set.....and i will let you guys know it all works out