bigdaddeywalt
New Member
- Messages
- 98
- Location
- beltsville MD
Thanks BlownSC, so the 335rwhp you acheived thruogh ur dyno was at what psi level? KEEP US POSTED
Stock 1UZ @ 11.07 ET
- Thread starter Blown SC
- Start date
The 1UZFE EGR Delete Kit is available for sale here.
That sounds about right. I think I'm at around 400rwhp. Made 350rwhp awhile back when I was trapping at 109mph, now usually around 115mph.
My best 1/4 to date is 12.047 @ 115mph (ish) in an SC400 that is a little bit more than 1000lbs heavier than your car.
Great job and good luck with the 10's hunt. Get that 60ft down a little.
KC
Blown SC
New Member
- Messages
- 128
- Location
- Queanbeyan/Australia
Update,
Put 398 RwHp on Saturday night on 15.5 psi
Put 398 RwHp on Saturday night on 15.5 psi
stevechumo
Active Member
- Messages
- 3,054
- Location
- OC, City of Sunshine
That's what I'm aiming for and I'll be happy to take a break on the engine for a while.Update,
Put 398 RwHp on Saturday night on 15.5 psi
kc95sc400
New Member
- Messages
- 524
- Location
- Charlotte, NC
Update,
Put 398 RwHp on Saturday night on 15.5 psi
That sounds about right. I think I'm at around 400rwhp. Made 350rwhp awhile back when I was trapping at 109mph, now usually around 115mph.
My best 1/4 to date is 12.047 @ 115mph (ish) in an SC400 that is a little bit more than 1000lbs heavier than your car.
Great job and good luck with the 10's hunt. Get that 60ft down a little.
KC
JustenGT8
New Member
- Messages
- 2,432
- Location
- Canberra, Australia
Neil is low on power on a very safe tune I've seen the size of the turbo and it's good for better than 400rwhp on 16psi....best my twins have done to date is 445rwhp on 10-11psi. With a more aggressive (but still safe) tune he should get at least 450rwhp on 1 bar.....still, it does the numbers at the track and is safe so not like you wouldn't be happy
I've seen the size of the turbo and it's good for better than 400rwhp on 16psi....best my twins have done to date is 445rwhp on 10-11psi. With a more aggressive (but still safe) tune he should get at least 450rwhp on 1 bar.....still, it does the numbers at the track and is safe so not like you wouldn't be happy bigdaddeywalt
New Member
- Messages
- 98
- Location
- beltsville MD
Great news, so I think Im on track because im also using the stock auto tranny like you and kc95sc400. I pushed out 312rwhp and 355rwtq at a mustang dyno, and my car weighs 2595 full trim. Once again great job.
stevechumo
Active Member
- Messages
- 3,054
- Location
- OC, City of Sunshine
Don't push any further with this auto tranny, unless you rebuild it with hi-performance kit. You're on the edge. Mine broke right at 334 rwhp and 371 rwtq after a week. I believe there're others running this complete stock tranny broke somewhere around there.
JustenGT8
New Member
- Messages
- 2,432
- Location
- Canberra, Australia
Neil uses some mutha of a Holset diesel truck turbine so gotta be 1.15 a/r at least is a T4 frame?
I use K26 housings (x2) on mine which are smallish so around a 0.6 a/r at a guess?
I use K26 housings (x2) on mine which are smallish so around a 0.6 a/r at a guess?
