Search results

Maybe it dropped a coil And is only running on 4cyl. It's happend to me a couple of times with those symptoms

So I pulled it down to find two broken pistons. The ring lands on cylinder #1 were broken top and bottom and cylinder #7 was broken on bottom. The big end on #1 has uneven wear through to the copper. On 7psi and only making 305rwhp I thought it would have lasted longer then that, maybe it was...

Hey guys. 1uz remote turbo in a 2wd hilux running 7psi has started venting smoke out of valve covers. Can you boosted guys shed some light on what you have done with your PCV valve. Mine is disconnected and are vented to atmosphere, should I have done it like this...

Thanks guys, looks like ill be up for a R154 and new bell housing. May have to wind it up just to see how far it will go

Hey guys, This is a question For those that have w58's behind a 1uz. At what power/torque do they go bang? I know torque is the main thing that kills these boxes and some people claim to have put upto 500hp through them but I can't find any behind a 1uz that let go. My setup is a 2wd...

Couldn't have done my conversion without this site! I don't post much, but I've been on here every single day since 08 Donation sent Phil

I drilled mine in the bottom of the fire wall behind clutch pedal and put a grommet in it

Pm sent. I do have a ecu hold power relay in the relay block, what channel should this be set to?

Yeah factory IAC. Ignition switch is digital input-2. Haven't done anything for ECU hold power. Unsure of firmware mate, the ecu is two weeks old, would assume its the most current

Forgot to mention as well that it wants to idle around 5000

This is my first ecu mate. Just spent the last 3 days trying to get my head around everything in pclink. I just sit there until it starts making sense.hehe. I used a basemap from the link website and change the AUX ports and everything to suite mine but it didn't work and I ended up with a flat...

Kind of don't understand what u mean gloverman. pretty new to the aftermarket stuff mate. I've wired the linkg4 with a complete harness i had made up over in christchurch, running 320cc 7mgte injectors, stock igniters, stepper motor, MAP, boost Solend. hx40 turbo, 7psi etc, etc. I'm about to sit...

Hey guys, I've just completed a rear mount turbo on on my 2wd single cab hilux using a hx40. I would like to know if anyone has a half decent basemap for a linkg4 extreme for non vvt. I've moved to central old and i have to drive it 8 hours for a tune. will post pics this Arvo. Cheers Phil

Have u thought of running a surge tank with a lifter pump? I have a 1uz hilux but I'm running a Bosch 044 external pump. When it's gets to a 1/4 tank it will surge and carry on only if I drive it hard. Just been to lazy to set the surge tank up so I drive it nice from a 1/4 tank on

Has anyone done it yet??? its been a few years since this was posted. would love to see a single set up (if its possible)

bullet cars (bulletcars.com.au) make fly's to suite w58. not much of person that knows stuff but they make the kits to suite 5 speed w58's. check there site

Its all standard mate, for the moment, its got a big single piece in it

Hey guys, after getting the shits with the crown auto having a mind of its own and shitting itself i decided to go with a w58 manual conversion. It is now complete and everything was fine until i took it on the freeway, i felt a slight vibration at 100km/h and didn't think much of it until i...

Naa Its not in limp home mode mate, pulled codes and had 56 and TPS sensor. The rev cut is only in N and Park. It will rev to 6500rpm in drive but if i diconect the ratio box i have a engine cut in gear. Its fine to drive, drives beautifuly, i just don't have manual 1st or second. I think i'll...

Yeah mate got the lot from venom. I unpluged the ratio box, but it just cuts out around 2500, is this because theres no speed sensor? i thought the ratio box took over the speed sensors job. if i chuck the ratio box what goes in its place? Is it easyer put the old transducer back in and get an...