Search results

You can use the Z418 or a Z386. From memory, the Z386 is a little smaller. This is the fitting I had to have made to clear the chassis in my MS46 Crown. http://members.optusnet.com.au/corona2jzge/Crown%20V8%20conversion/In%20place/oil%20distribution%20block.jpg

Corona Mk2 or an old MX32 Cressida. And we all know what I think of sleepers.

Ford wheels 114.3 x 5 PCD. A 14" rim might fit but I had a couple of 15"s so I used those.

For MAP, you run a small vacuum line from each throttle to a vacuum cannister and sense the pressure from there. This will stop the wild oscillations in pressure you would expect to get from just sensing pressure from one throttle. For AFM, you make a sealed box like a plenum. Make a big...

I think the silver top throttle bores are 40mm, whilst the black tops are 43mm. 40mm would be the smallest I'd go. I have a 2JZGE with ITBs and they are 48mm. With all the supporting mods, I'm hoping they will be the right size. The improvement in mid range response even on the standard...

You could probably go to 12:1 running 98 RON, a good aftermarket ECU (read MoTeC) and excellent tuning. If you wanted to go higher, you could use any of the racing fuels. Obviously, you would only maximise the benefits with supporting modifications (cams, intake, exhaust, etc).

Well she's up and running, drove it to the exhaust place with it running straight out the manifolds - glorious. Twin 2.25" system with high flow cats, mid 90's dB. Changes gears beautifully, steers beautifully. Hopefully I'll be down at the strip next weekend to see what she runs. Looking...

The reason why there is a slight angle introduced is that with rotation of the tailshaft and pinion, there is a natural tendency for the diff (pinion shaft) to rotate upwards under load. Leaf rear ends are looser, so they will rotate upwards more than a multilink rear end. The idea is to get the...

Whilst many people reference pinion angle to the horizontal, it is actually the difference between the crank plane and the pinion shaft plane angles. The pinion angle you want is dependent upon the type of rear end you are running. With a leaf spring rear end you want a pinion angle of...

Just remember that the bellhousing is actually part of the gearbox case on the V160/1. As well as any machine work, you better factor in disassembly and reassembly of a fairly fancy box. http://www.turbosupras.com/images/technical/V160/gearbox%20getrag%20top%201.jpg Thanks to Jon on...

Pics of rack and pinion conversion: http://members.optusnet.com.au/corona2jzge/Crown%20V8%20conversion/rack%20and%20pinion%20conversion/ As you can see it needed a bit of grinding of the sump to make clearance. Love the 240C. That's a beast.

The fitment was easy enough but it is tight. There is about 15mm clearance each side of the exhaust manifolds to the chassis rails. Also the RHS bank of cylinders wanted to be intimate with the steering box, so the steering box had to come out and a VN Commodore power steering rack has gone in...

One day 2 years ago, I was driving along and spotted a mint 1966 Crown Station wagon. One owner but blown head gasket. I bought it that day. Drove it home, swapped the motor over for a spare 4M and drove it around for a few months. Then I took for a drive to the country and a split hose ensured...

High Energy Oil Pans 6a Short St Dandenong 3175 (03) 9794 9075 These guys make custom sumps, but unfortunately are very Ford, Holden and Chev oriented. They didn't believe Toyota made a V8 when I spoke to them, but were prepared to have a look at the sump and have a go.

I am dropping my Crown 1UZFE into another much older Crown. It is a 1966 Toyota Crown station wagon. It's turning out to be quite a job. The mounts are pretty straight forward but unfortunately I have had to do a rack and pinion conversion to make the thing turn - the steering box wanted to...

Tony, for my application (Toyota Crown) I'd prefer to not have them poking out of the bonnet. Can you give a rough idea as to how high they sit up (say in comparison to the standard plenum)?

I'd check the pinion angle. Buy a magnetic roofing protractor and measure the angles from vertical of the engine pulley and diff pinion face. With the IRS diff being rather solidly mounted in the diff cradle, you'd probably only want a maximux of 2-3 degrees of pinion angle.

You could try the www.is300.net forums for more advice. Quite a few guys there have undertaken this conversion. Be sure to do a search before asking questions otherwise expect to dealt a harsh newbie welcome. NA-T is where you turbocharge you existing NA motor. Several companies sell kits for...

Lovely product. Very competitive price. Big thumbs up. Which 20V 4AGE throttle bodies do you use? Silver top or black top? I think the silvertops whilst being more readily available have a slightly smaller bore than the black tops (40mm vs 43mm I think - please correct me if that's wrong)...