Search results

  1. V

    Spitronic's forum

    hi Alan,dont know if you are aware but there is a uk distributor of spitronics, Andy Bird at race systems. https://www.facebook.com/racesys
  2. V

    Do I need a rear waterbridge.

    this is what i did with my water bridge, can anyone see any reason it wont work? would i be better linking it to the front water bridge aswell.
  3. V

    Block water connection near oil filter housing

    i would use a short length of rubber hose with a bung in the end, the other way is to buy a drain plug like the one on the other side of the engine and fit it to the block instead of the water outlet
  4. V

    1UZFE Sump Flange AutoCAD drawing files

    it was £25, i had mine done in bradford but there will be loads of laser cutters closer to you than that, one thing i noticed is that one of the bolt holes is slightly out, i just drilled it 2mm bigger and the bolt went in ok.i messed a few up but what i had left over are on ebay.
  5. V

    Bellhousing to Engine block CAD file

    i sent you an email, thank you
  6. V

    cad file for inlet manifold plate

    i need the flanges that bolt to the cylinder head to make an ITB manifold. do you have a file for them?
  7. V

    cad file for inlet manifold plate

    i have read loads of post on here with cad files for all sorts of things to do with the 1uz but when i want to download them they are dead ends, i would like to make a library of cad files for the 1uz-fe engine, i have a sump flange, cat flange and the oil filter relocation plate that i would be...
  8. V

    Upper Inlet Manifold Cad File

    any pictures of your tvr?
  9. V

    Bellhousing to Engine block CAD file

    hi jake, would it be possible to send me the cad file too, i am trying to mate a mazda rx8 gearbox to a 1uz, thanks
  10. V

    Upper Inlet Manifold Cad File

    sounds like we are going in a similar direction with our engines, what is yours going in to? mine will be in a mazda rx7
  11. V

    Upper Inlet Manifold Cad File

    any pictures of the inlet manifold yet, if its as good as your sump it should be a thing of beauty.
  12. V

    Inlet Flange

    hi Alan, i was thinking about getting this from ebay, have you had the flanges cut yet and were they ok? the inlet manifold studs on my engine are at a funny angle, does this flange take that into consideration or would i need to make some angled spacers.
  13. V

    Twin Turbo 1UZ goodness!

    that was a hell of a drive to keep it out of the walls, it could have been a lot worse.
  14. V

    Where are you located?

    God's own county, yorkshire,uk
  15. V

    Spitronic's forum

    interesting stuff, i might take you up on that offer when i get to that point, it may be a while yet though, thanks. not sure if it is of any interest to you but i started a facebook group, 1uz-fe swap parts uk, for people to chat, share ideas and find suppliers in our neck of the woods . Leigh.
  16. V

    Spitronic's forum

    hi Alan, im guessing that you have a spitronics system, is it any good? i was thinking about getting one for my project, it cheap compared to the other systems which, as a yorkshire man, i find appealing. what are your thoughts on it.
  17. V

    3vze flywheel issues

    the bolt holes on this flywheel look very wrong, i would not use it,i know the flywheel centres on the crank so the bolts only need to stop it turning but even so they just don't look right, it came in a kit from collins racing(?) so it is probably tried and tested, its just not for me.
  18. V

    mazda gearbox?

    the cheapest i have seen is £1500. where did you see one at that price, might be worth a look
  19. V

    3vze flywheel issues

    i recently bought a 3vze flywheel and took it to my local machine shop to have the back taken out of it, they looked at me like i had three heads,they would not do it because it might fall apart, do you have a picture from the rear of the flywheel so i can show them it and say "look, this guy...


Top