Search results

its a lexus auto with lexus wiring the wiring going to the gearbox is the selector switch, speed sensors and transfer motor. i tried the red/black wire at the ecu but there was not 12v

I have a 91 Surf with 1uz and auto I have no reverse lights and cannot see how to get them going. If I could find the output from the gearbox or ecu i could run a relay and wires to the back and get it going. I even thought about running a microswitch on the shifter, but cant see a good...

seems like it is the starter that needs to come out is there a guide somewhere how to get this out? I am stuck with at the injector/fuel rail remaval part.

After heading out in the mud the other week the 1uz started running rough. i thought thats ok, petrols do that sometimes when they get wet. but when i got it home it would start and run fine for a couple of days, but now the starter motor wont run at all. i checked the ECU output and there is...

yeah i certainly didnt assume it would be easy, part of the reason that i bought one that was meant to be already done. motor was put in by a mechanic and wired up by an auto elec, they both did an unbelievably poor job.

getting really tired of these issues, but put a bit of time in to try to figure it out. tried with each ignitor unplugged, no change with #1 unplugged but without #2 it would turn over but not fire at all. traced the wires from both ignitors, all seem fine but IGT on ignitor 1 has a bit of...

I have the same problem. Was fine, then started to die while driving, now wont run once started, only for about 2 seconds. checked codes again and now get 14 (no IGF1 signal to ECM for 8-11 consecutive IGT1 signal) and 78 (fuel pump) , as well as left and right oxy sensor, but it would run with...

looked at the diagram and it was easier to use a tast light. did a bit of searching the net for the pins on the diagnostic plug (on the engine) and worked out which to put the light on. Tried a 10mm wedge bulb (like indicator/park light) but that didn't work, so tried an LED indicator and that...

Ended up going the cork gasket. Sucked to get it on but not as messy! so far no leaks, did put on my other pan that looked a bit straighter. Finally took it for a drive, was ruinning at operating temp for about 20-30 min before it would die for a second, then come good again. Did this about 5...

I think thats the exact one I used, ultra black or something. I cleaned it really well coz i wanted it to be spot on. A bit worried to try it again tho, really really really dont want to have to do it again.

std hugger headers into 2.5", high flow cat, muffler, sounds more "notey" than i expected, happy with it http://www.youtube.com/watch?v=s02-ISXvCto http://www.youtube.com/watch?v=yFHBhm14ug8

what type did you use? i removed mine on the weekend which was a prick of a job because the exhaust is so close to the front edge, i could only tilt it down i little because i couldnt get it all the way off. I removed the cork gasket and used silicone instead. I left it overnight then...

i have a couple diagrams for the transfer wiring but they dont match up. i went to the wreckers and traced the wires of a later model (had two plugs top left of transfer and electronic speedo) and cut the motor plug and transfer indicator switch (which didnt help). When i went to wire it up...

thanks, its getting there, slowly! yeah tyres are 33s, but didn't feel quite right with the 30s either. had a look at the process to pull down the transfer case to swap the input shaft and it looks quite involved. Might be the only option, and at least it should end up being more reliable.

Still having trouble with the transfer, there is no wiring so i need to get it to work without the 4wd computer. i know that people have done it, im just not sure how. I have this diagram

Hi earthman Still working on the vehicle, but have done about 50 kms in short trips and the gearbox seems fine. Changes up and down, and kicks down when i sink the boot. I wouldn't say its that quick tho, just doesn't feel like it is pushing along properly. Found the oil leak, when the...

gearbox is in, works good. But doesn't seem like it has enough drive tho, doesn't seem to pull up hills like it should, seems slippy. maybe that is just what they are like? using genuine toyota type t IV atf. now i have an oil pressure guage and it seems like a lot of pressure. about 90 psi...

swapped the wiring over no worries, hoping this works. box is back in vehicle with transfer. what ATF should i use? was using Nulon synthetic last time. any idea of quantity? seemed to take heaps last time but not sure exactly how much. what is the method for ATF distribution through the...

oh and they do have two black/red wires with 12v with ign on.

i pulled the plugs and wiring out of both gearboxes and put the one that matches the loom in the vehicle (the one with temp) into the replacement gearbox. im hoping that this works. Both look the same apart from the temp so that make sense. so just to confirm, if something is wrong with the...