Search results

1uzfe hole pattern cad and DXF Hi guys I haven't got the th400 pattern but here is the 1uzfe one to get you started.. The holes at 90 degrees are ones at the bottom of the bell housing so you are looking down at the face of bell housing (remember to rotate the right way round when you set...

exhaust port centres.. Hi LEXUSA Sorry bit slow to get back to you been away on holiday with the family. The exhaust port centres are 105.5mm between all 4 exhaust ports. From the centre of the back exhaust to the back of the head is 100mm. Also managed to figure out what I am going to...

something like this... Hi FoPar Ive been enjoying reading and seeing your updates and must admit to learning a lot. Thought you might want to have a look at what Autronic and I have been up too. I'm very interested in the comments on the intake manifold as a couple of weeks ago I...

Cheers xirforever.. Thanks for the info.. Craig

mig wire uses.. Hi xirforever We just picked at the air bubble with the mig wire, sort of lifted the bubbles to the surface and then popped them. I am interested in the price of the product and how much you get for that price? Great job by the way, looks factory made... Cheers Craig

little trick.. Hi xirforever Years ago when helping a mate to pour clear resin beer handles we used to use mig wire to remove air bubbles until one day after mixing in the catalyst the phone went. Pouring the mixture was a little later than usual but all the bubbles had gone. Maybe with a...

Cheers LEXUSA.. Thank you for the information. Small things like these are what will help to end up making a great toy even better... Your help and time are really appreciated. Any time I can help just ask... Cheers Craig Young

exhaust port dia.. Hi LEXUSA Sorry not sure about lift and duration and valve sizes... Hope someone out there can help.? The 33mm size that I referred to is the exhaust pipe dia. about 18mm (as far as internal jaws on vernier will fit) down the inside of exhaust pipe. And the 34.8mm...

Engine specs... Hi LEXUSA The engine I have is early 1uzfe (non vvti) it has 0083329 stamped on it. The ecu has 89-94 celsior (sorry about spelling) written in black pen on it but I know it is not a matched to the motor (planning to run link anyway) I am planning to run motor as is without...

exhaust port dia.. Hi LEXUSA The exhaust ports are 34.8mm top to bottom and 35.8 side to side. Hope this helps.. I am interested in your software because I have to make an exhaust system for a mid-engined 1uzfe and a lot shorter than that for a car with motor mounted in the front. I...

Hi guys.. I ended up making a cover plate too.. Good luck with the project Cheers Craig

nice.. Well done nice ride.. Cheers Craig

try this... Hi Hiluxfan When I got my rocker covers powder-coated i had to remove and replace the spark-plug seals just like you. What I did was used a power-file (like a small belt sander)(Black and Decker i think) to remove the top of the aluminum rivet flush with the baffle plate then...

how about sending 3D files my way... Hi guys I reckon I could beat that price for your flanges even with sending them half way around the world... Here is a couple of sets for a 4age trumpet adaptor that I made middle of last year. They were $100 NZD per set and were out of some 10mm 6061...

made an oil pump not long ago... Hi guys The other reason for failures is the material that the oil pump inner and outer ring are made from powdered metal which is then compressed and heated as opposed to machined from solid. Late last year I made a set for a company that they used in a RB26...

... are spherical bearings any better...? what is the best set up...?

cams from solid bar Hi Redrocco I had a customer recently ask about the extact thing that you are planning to do... He grinds cams for a living and does low numbers and one offs for all sorts of vehicles (jet skis etc.) I priced up for at a local company with a lathe that had live tools...

post a photo please.. hi guys I would happily look at making a couple of sets but could do with a photo or two to see what I would have to make.. If you could send a 3d cad file that would speed things up even more.. Cheers Craig

next time then.. Hi ALI1UZLUX Nevermind... maybe next time To all out there if there is something that you want CNC machined and you think that you could sell then I am all ears (even better if you have a 3D cad file) then I am happy to quote for a run of 5 and see if we could make some...

thanks ALI1UZLUX.. Sorry to be a pain.. Yes I did post this up to generate interest and show people out there the adaptors and in a funny way it does generate sales for my machining centre. You mention a sump for your motor, is it a dry sump and do you have a design? (ie 3d cad file) if so...