Search results

If i was over there in aussie sideshow id let ya have my Soarer Auto to play with and see if that makes any difference. I just got my hilux ute back up to hamilton and did a short trip between my sisters house and my flat, appart from running hell rich, it seems to pull it self along nicely...

Sounds good to me, see ya all there.

dude your 1UZ V8 must have something wrong with it if your comparing it to a 308. I used to recon 308's and never found a standard one that bolted in or ran as good as the 1UZ seems to. not to mention the fact that 308's weigh a tonne in comparisson. On a Link factory tune my 1uz has more power...

hey sideshow, Someone called your Hilux a slug?? I took my one for its first drive this weekend. It sure wasnt a slug but im running the after market computer(not dialed in yet), headers(factory) and supra 5 speed and i thought it went well. Maybe you should just work on doing an after...

Ok im guilty for slowing this project downa bit as i "borrowed" the alternator and the thermostat housing of gloverman's 1UZ, Dont worry all will be returned asap...My ute is going i just need to steal it back off my father!!!... As far as the sump is concerned i think the rear sump 1UZ will go...

Zuffen, I would but i just installed my box back into my ute and i cant remember what i did with that info. If you have sketches with dimentions e-mail them to me and i'll see if i can CAD it up for you.

Soarer Turbo?? That would be the 2JZ model i think...So you would need either a R154 or W58-57-55 with a J series gearbox (i cant recall what the shifter position needs to be). There are a couple of clutch set ups the push pull type and the standard push type, depending on your box and what...

which pinion?? You have your input shaft with the spline with the sliding shaft collar over it?? I think I get what you mean, you are just going to cut your bellhousing and weld the 1UZ bellhousing engine side on to it?? I could do it in CAD but would need a pretty accurate drawing of your...

Hey Lowboost, Here is what i have drawn up in CAD to set up my clutch. I hope this is what you were looking for. If it hasnt reduced the scale is 1:2

i have about 5mm between my steering universal and my header and i havnt got close to it when iv revved the engine, your engine should rock away from the chassis on that side when you rev it so you should be sweet. otherwise if you had the hydrualic fan pump you could use the banjo off there and...

I have them in CAD, I will check my files at work tomorrow and post them for you. Here are some bell housing pics if they help. I think, from what i have heard the mr2 gearbox's run the same gearing as the W5* series gearboxes, mite pay to check but i think you can also upgrade the input...

Hey Rusty, I have just blanked mine off and im using the Link, and yeah the revs die a weee bit but its not too bad. I am running the remote 1UZ power steer pump but it should be roughly the same as yours.

yeah if you want your engine to sit far back the rear sump should work no problems, i had the factory rear sump motor but swaped to a front sump so i could locate my engine in a more servicable position...i still had to notch out the back of the bowl though so the steering arm could arc...

How about second weekend in November??? Yup Kalvin you can hitch with me, you can man the Link controller if ya want. Be keen as to see that RX7 and see how they got that in there..have you seen the black series 4 with the supercharged 1UZ running around??

Sure the price of petrol is rising but i havnt heard anyone complaining about paying over $2.00 for a bottle of water???? Realistacally the only way to bring down the prices of petrol would be to put some bio fuels in place and create a bit more competition. Here in New Zealand we have an...

Here's my oil filter position in my Hilux, this is standard on the SC400 rear sump motor and its running the Z418 oil filter with plenty of room. I have switched the bottom tank radiator hose to the opposite side so it makes this a little more sevicable, but basically this set up works as good...

yup november sounds a lot better, at least by then i would have ironed out my woes....

Hey Guys, Umm give me 3 weeks and i should be all cert.'d and good to go. I towed my ute into town this morning to get the headers extended. So all going to plan tomorrow afternoon the Link V5 ECU can begin to be installed. Still waiting on the sump to be modified and the drivshaft to be...

6pk1650 will work if you bypass the pump and remove the aircon. thats the repco part number and its a gates belt

There is a guy here in new zealand getting 460hp out of a 1uz-fe in a Toyota SR coupe. From what he says, its an early model 1uz from a crown with headers and a pod filter running through a Link V5 ECU....however its tuned to within an inch of its life so reliability would be an issue. W5*...