Search results

  1. G

    Update on Paul Carey UZFE powered Drag Car

    I believe Eric at ttcperformance.com has access to those cranks. When I spoke to him about Sonny, he did not know that was who made them, but he apparently has access to purchase them, so I'm assuming he gets them through TRD or someone at TRD
  2. G

    Update on Paul Carey UZFE powered Drag Car

    It's possible, just not very plausible, the cast mold would be way too expensive unless the market was of the small block chevy and thousands would be sold in a short amount of time to make up for it
  3. G

    Siamese'd Cylinders ?

    I can't find anything on the UR either Can you post what you have at least? Maybe start another thread dedicated to finding info on the UR motors, on the web?
  4. G

    Siamese'd Cylinders ?

    The 3ur crank would not fit into the 2uz block You'd be much better off just getting a custom crank out of billet
  5. G

    =crankshaft Modifications=

    :la: :lol: Great article by the way
  6. G

    Siamese'd Cylinders ?

    The heads cannot be interchanged, checked that too
  7. G

    Siamese'd Cylinders ?

    They do have the same center to center, I bought a head gasket for the 3ur yesterday and measured it, 105.5 or 106mm, center to center. I doubt the engine is shorter in height, it has a much longer centerline to bore to achieve that stroke
  8. G

    Does anyone have 2uz block prints?

    I know this is probably a long shot, but anyone?
  9. G

    2007 5.7 Tundra Motor

    That is good! That will make it a very popular motor for the aftermarket :D
  10. G

    New Intake Plenum

    Where's my manifold? :thinking:
  11. G

    Auto cross/Road Racing car ... 91 MR2 with a 1uz

    Jeff, We spoke over email already :) I'll continue to email you, thanks
  12. G

    1UZFE/2UZFE into a 2nd Gen 4Runner (U.S.)

    This is all the external wiring that is needed to get the 1uz to start??? To make my question more clear, I could put this motor in a tractor, and hook this wiring up and get it to start!!!???
  13. G

    2007 5.7 Tundra Motor

    It's going to take forever for that to occur :argue:
  14. G

    What are the largest Lexus junkyards around?

    Well, I guess I'll give it a try
  15. G

    What are the largest Lexus junkyards around?

    Thanks! I called, they said "No Sir" :(
  16. G

    Parts FS: 1998 SC400 vvti vehicle

    All PM's replied to For clarification, this is not a car that can be made road worthy again ... it'd make a great drag race platform, but the value is in the body parts (minus the trunk/side) and the drivetrain, axles, rear, brakes, suspension
  17. G

    What are the largest Lexus junkyards around?

    Haha, I'm looking for 06+ models
  18. G

    Parts FS: 1998 SC400 vvti vehicle

    Bought this from Gazi, and then decided to go a different route It's a 1998 SC400, with a vvti motor. The car does not have an interior, but it will start, move and run, and it was hit slightly in the rear. It is red in color Gazi will atest to the vehicle I'm sure So you can get...
  19. G

    What are the largest Lexus junkyards around?

    Anywhere in the states I guess
  20. G

    New Lexus LS600! in Aust Sept 07 - 327kW and 820Nm

    Sweet, so it's going to have the 2ur motor?


Back
Top