Search results

  1. V

    My Latest converion

    I've got my engine to fire up today using a Delco/Kalmaker computer with one of Richards boxes. After chasing a problem which turned out to be two faulty ignition modules the car fired first go and ran well for a car with not much of a program in the computer. Now I need to get a emmisions...
  2. V

    powerglide behind a 1uz

    I used a Crown bellhousing then had a plate made to fit a 6 cylinder glide
  3. V

    Lower Boost

    Series 4 RX7
  4. V

    Lower Boost

    There a sealed factory actuator for the internal wastegates.
  5. V

    Lower Boost

    I've been trying to think of a way to run 5 psi boost when my wastegates open at 7-8psi I'm thinking if I hooked up an electronic boost controller to an air receiver and the compressor off the crowns air suspension and regulate the pressure to about 20 psi that way when I reach 5 psi the EBC...
  6. V

    Tiptronic Controller

    Let me know when you are making these again kdog because I need one.
  7. V

    Bell Housing Review - Powerglide + 1UZ-FE

    I had my adapter plate made it fits the 1uz bellhousing to powerglide I just took the both of them to an engineering place and it only cost $200
  8. V

    And the Winner is......

    Interesting result. We are playing with a fairly hi-tech V8 yet most people prefer an old school look.
  9. V

    Seller Feedback Some body to watch out for

    I sent an old sump I had left over up to him. So he should be right now.
  10. V

    My Latest converion

    Haven't run down the drag strip with turbos yet it ran a 9.4 1/8th without turbos. I don't want to fit a roll cage so I'll stop chasing horsepower when it runs 11.5 1/4 mile. I've got to get the rocker covers and one turbo compressor housing polished.
  11. V

    My Latest converion

    My Latest conversion This is my latest toy. Its going to be a tow car for my drag car. http://gallery.910bluebird.com/1UZ-910
  12. V

    1UZ into MK1 Ford Capri

    They must be I've got 2 1UZ powered Capris. I ones going to be supercharged using a jag supercharger. The other is twin turboed and running a powerglide.
  13. V

    1UZ on an aftermarket computer

    How is the kalmaker not cheaper than almost every other programmable management system. I thought Richards box is designed to be used with any system.
  14. V

    1UZ on an aftermarket computer

    One of them would be mine. I hope it works as good as you say they do. If it is it will save me a lot of time and money. By the way he spoke he hasn't sold many which is a shame because he put a lot of time and effort getting it right.
  15. V

    Stock Soarer Timing map

    yes it did go above 40 degrees a couple of times
  16. V

    Bodykits For Sc400

    I've seen someone selling them on eBay http://search.ebay.com.au/_W0QQsassZteam.jds and he has a web site www.jds-auto-imports.com
  17. V

    Stock Soarer Timing map

    Results I've been to the dyno this morning. We had a bit of trouble getting rpm and vacuum spot on but I think its close enough.
  18. V

    Stock Soarer Timing map

    I'm thinking mapping the air fuel ratio might be handy to have. I'm going to try and do this next week is anyone else intereseted in results or have any ideas on what else to log while I've got the car on the dyno?
  19. V

    Stock Soarer Timing map

    Has anyone put a stock Lexus on a dyno to get some timing points to make up a timing map for an aftermarket ECU?
  20. V

    fkuc these headers!!!!

    Why are you making them out of steam pipe?


Back
Top