Search results

It has happened I am married and don't have time to give my Dato the time she deserves. So it is up for sale hopefully someone else can treat her the way she deserves. Summary Car 1976 Datsun 260z 2+2 recent low king springs and new munroe's 16" superlights brake upgrade: Front 260mm...

Does anyone have a Fulley of the back of a crown Viscous fan?? I have had my car off the road for ages and i do mean ages. one of the few things i need is a Viscous Thermo fan Pulley. I am changing from Hydralic fan - Electric Thermo and i am using the Crown housing as a idler for the fan...

Hi guys it has been a couple years since i have posted but now i need help. I replaced the engine and put in new cams NA car and it never ran very cool bit of a head gasket leak eventually it got bad and i gave it new ACL head gaskets and skimmed the heads. since then it has useda a lot of...

When I pulled my original cams out I noticed the locating pin in one intake cam was bent. I have since put the new cams in the vehicle and it has been going slightly down hill. I am nearly 100% sure that the gear is moving on the cam and this is what is giving me troubles. I did the cam bolt up...

I have swapped from a lexsus 1993 block and heads to a 1992 crown with exactly the same intake and extractors what will be the power difference?? After market managment so computers don't come into it

What is the limit of a stock bottom end? speedway guys in NZ are getting 10 and 11 thousand RPm but that can't be stock. I have a stock crown bottom end and am a week off fitting Cams 370 thou lift before clearance 240 @ 50 and some new springs to handle it. So the question is how hard...

i went to the track and suffered oil surge and a spun bearing. if any one has any ideas on how to baffle the sump i am interested.

last week the zed started shifting on it's own not cool at all in mid corner. (for those that don't know i run a shift kited valve body and a tiptronic setup) then on the weekend i was at motorkarna giving it a real floggen. it would shift weirdly mid drift and stuff but still did good skids...

I just found out. trying to push the 260Z round some corners in the dry proved a little too much. the outer uni let go sheared in half no small failure here, thumped around for a bit till i came to a stop. so i think it is time for CV half shafts Just thought i would let you all know 233RWHP...

At Brisbane Motor Show on the weekend and say this not bad looking kind of contach rip off running a 1UZ they had a fully complianced NA car and a Twin turbo PWR barrel cooled Chassis. The guy i spoke to knew not a lot they were buying the motors referbished from Forced Air Technologies. it was...

A mate with a Vl runs 13.6 on street tyres and 12.8 on slicks this thing has credentials, he has always looked at me as not quite worthy. the other day we lined up from a standing start no lights but a fairly even launchi probably get just under two lengths on him in first gearand he slowly...

My car has always run at 14 volts like a dream but it wouldn't idle so i took it in to get looked at and it is running 11.8 volts not getting enough fuel at idle and running like a dog fuctuating from 900-300rpm sounding like it is missing if it does not stall. i have never wirred up the...

I just fitted a stage 1&1/2 shift kit from MV automatics in Adelaide. BUY one they rock no more bogging down no more watching other people get a length or two when shifting. a quick chirp and it is off again 1-2 2-3 this rocks.( havn't triep 3-4 yet as it is doing 180 kmh at the top of third)...

looking at puting A/C on my zed changes in ADR's as of january 1 2004 mean you do not need a heater is your demister can remove condensation from the windscreen. so out with the heater and in with a A/C it will still be legal ( as legal as it was before) any way i have a sc400 motor and am...

pulled up alongside this thing near new beautiful in silver E55 AMG merc, old guy driving of cource who els can afford it. and he gave it a stab. followed along for bout ten minuites he wasn't keen for a run off the lights, but he did give it a good quick run from 50- 80 when the road opened...

Just a few photos of the ZEd i will get some more Tech photos now that we can upload. (soon)

has anyone seen or fabed up a gear shift extension to relocate the shifter back so it comes up through the right hole i think i have to move it 200mm or so i am off to measure at lunch. i was thinking a 3D seesaw which would swap let to right and keep 1st at the front still. I am throwing this...

Mine has burnt out the 2nd gear brake band i am told. if someone out there has one they don't want cluttering up their gararge.

K dog is the guru on this front but others have experience too and this is one nut I want cracked as many people are interested in getting this box to work the way it should sharp and sweet. who has hydralic diagrams? is the pressure solenoid PWM or variable voltage? I am running a a340 i...

I am looking for expresions of intrest i need around ten orders for cams so i can get Tighe Cams to make castings for the 1uz-fe. these can be ground for FI syestems if that is what you want. Cast cams will have the benifite of standard base circle diameter and oposed to welded cams they will...