Search results

  1. sniper

    Parts 1UZFE 3UZFE ARP Head Stud Kit $300, Genuine Dellows 1UZ-> R154 Bellhousing $550 PHX

    ALL SOLD Genuine APR Head Stud kit for 1UZ/3UZ Brand new condition. $300 paypaled Genuine Dellow's 1UZ -> R154 Swap Bellhousing, with fork and throwout bearing. $550 paypaled Located Phx. AZ. Please PM if interested!
  2. sniper

    Parts Drive Shaft Shop Lightweight Aluminum Drive Shaft R154 -> 240sx NEW!

    Selling the aluminum drive shaft I had made by the drive shaft shop for my S13 swap. MEASURED length, (diff flange to seal) is 48 inches. OVERALL TOTAL length is 50 5/8. Brand new never used! $500 shipped to 48 states.
  3. sniper

    Parts Brand New VVTi 1UZ Water Pump Timing Belt Complete Kit OEM TOYOTA Parts!

    Complete water pump and timing belt kit for a VVTi 1UZ-FE that I bought from the dealer, but I sold my car before I could install them. Comes with Water Pump, new pump gasket, New pump bolts, Timing belt, Idler pulley, tensioner pulley, tensioner, Maintenance sticker, and the o-rings...
  4. sniper

    Parts (3) LS400 Front Sump 1UZ-FE Engines $150 bux each So. Cali.

    Everythings gone! Thanks!!!!!!!!!!
  5. sniper

    Parts 304 Stainless Steel 1.5" Sch. 40 Chamfered, 90 degree bends!

    I have 24 of these 304 Stainless Steel 1.5" Sch. 40 Chamfered, 90 degree bends, perfect for building turbo manifolds. $5 per bend plus shipping.
  6. sniper

    When should you lock tite your bolts?

    When custom fabbing stuff, what are some of the basic rules on lock tite? If I had a steel bolt that was threaded into an aluminum piece, say a flywheel, should I use lock tite? I'm assuming that with the two metals expanding at different rates, the steel bolt is going to make it's way out...
  7. sniper

    Manual swap in VVti SC400, any more issues than non-vvti?

    Does anyone have any thoughts on why additional issues would pop up when trying to do a manual swap in a 98+ VVTi SC400 vs a non-VVTi? The rear end wouldn't have to be changed because the VVTi has a 5 speed auto and a lower ratio, but would there be any more wiring issues to deal with because...
  8. sniper

    Seller Feedback Jake Breyck, uza70.com, a.k.a. quantum-auto.com 1UZ flywheel purchase, what a joke!

    I paid for my flywheel on 6/10/09 and it took 4 weeks (received on 07/14/09) for me to get a flywheel that looked just like the one marked "A" in the photo below. It was light and of an acceptable quality for the price. Only problem is, it doesn't work with 7M pressure plates like I was told...
  9. sniper

    Parts 6000K 9004 55W HI/LO beam bi-xenon HID kit for first gen LS400

    I have a Hi/Lo beam HID kit I bought for my first gen LS, but I had to sell the car. It's from sharpHID.com and has a life time warranty. This 9004 kit has a pair of 6000K bulbs, it's brand new in the box, never turned on or installed. Also comes with the slimmer, more powerful 55W basalts...
  10. sniper

    Cars For Sale 91 LS400 Shell Gray/Gray Las Vegas $100!!!!!

    SOOOOOOLD!!
  11. sniper

    Free 91 LS400 Exhaust minus cats, Las Vegas!

    I have the complete exhaust headers back to mufflers minus the cats that sit at the end of the headers. Come by and pick it up if you want it! please PM me for details.
  12. sniper

    CAD Drawing for intake manifold flanges?

    Anyone have a set of aluminum intake flanges for a standard 1UZ, or a file of them drawn up that I can take to a local machine shop to have them cut? Thank you in advance!
  13. sniper

    Pressure plate Identification help needed 2JZGE or 3SGTE?

    I was told this pressure plate was for a 2JZGE/7MGE application. But that does not seem correct. Can anyone verify if this is a 2JZGE or maybe a 3SGTE? pressure plate bolt pattern?
  14. sniper

    Wiring the LS400/celsior 1UZ ECU without the factory transmission?

    Some may have seen this post http://www.lextreme.com/1UZFE_Crown_Diagram.html It goes over how to wire a crown ECU without the factory trans. I have a LS400/celsior ECU which is different of course, here is a pic of it It is different from the one used in the article shown here, The...
  15. sniper

    Need help and advice before I pull this R154 apart please!

    So, I need to extend my shifter and it seems like I have to pull the back half on the trans apart in order to get the shifter piece out. Now im considering installing the Marlin Crawler R154 Thrust Washer. Anyone ever install one of these? I'm afraid of some spring, of washer or nut slipping...
  16. sniper

    Cutting and raising the oil sump for a S13 application? What to do?

    As some have seen, the 1UZ front sup sits very low when swapped into a S13. Has anyone modified their sump to sit higher? Dry sump would be nice, but that's a bit unrealistic at this stage for me...
  17. sniper

    Has anyone welded Titanium?

    Anyone ever worked with Titanium before? It is hard to weld? I have read that you have to protect the back side of the weld with an argon shield. And you should also use something called, a trailing shield? to protect the cooling weld. What gauge, or thickness tube would you use to build a...
  18. sniper

    Wanted Under dash wiring for 91 LS400 needed!

    I need the fuse box that is under the dash on the driver side, where the pedals are. I need the fuse box and all the plugs that attach to it. Simply cut the wires as far back as possible so I can use solder and make some repairs. Let me know with a PM!!
  19. sniper

    Parts 5 speed Swap parts, Dellow Billet Steel Flywheel In USA

    I have a new, unused Dellow Billet Steel Flywheel. Will work with R154 or W58. It is made to use a 2JZGE/SC300 clutch kit. The flywheel already has the ring gear pressed on and has TIG welds added to it. Longer flywheel bolts included. I bolted these parts up to my 1UZ just for mock up but...


Top