Search results

Anybody making stud girdles, windage trays and crank scrapers these days. Thanks Alan

Hi All. Is there anybody in Perth running the Spitronics ECU and TCU with turbos. Alan

Hi All Are there any serpentine aftermarket pulley tensioners so I can only run the alternator. Alan

Hi All This is on Facebook https://www.facebook.com/photo.php?fbid=10156146929735403&set=pcb.628612827241481&type=3&theater

Hi All Just got a box, was sold as a A650E 5 speed, the name plate says 30 50 LS, I think both are 5 speed. Question what are these out of and how strong are they, going on the back of a 1UZ-FE none VVTi (1994) engine, is the torque converter any better then a 340 Alan

Hi All Taken the old belt off and looked at the engine and thought it looked manky. so taking off the cam pulleys to clean up the metal plates for the plastic covers, you have to remove the cam pulleys, that's where the old belt comes in. Piece of tube 1 1/2", hammer and a M8 nut and bolt...

Hi, are there any billet pulleys made for the 1UZFE, ie , idler serpent belt and cam gears. Alan

Hi Will this gearbox fit onto a 1UZFE (1994 ) engine, I have a old 4 speed with the cable from the throttle, I think it's line lock up (correct me if iI am wrong). I want to replace the 4 speed with a 5 speed or even 6 speed if it's a direct swap. Alan

Hi Any body make blanking plates / covers for the distributers, I an using cop's so all the plug leads and old coils can go, just thinking it would look nice with cover plates where the old roters were Alan

Hi All There are 4 sensors on the front water bridge. what are they all for Alan

Hi I need to get some cop's, I have 2 part numbers both Denso, one is 0919-02238 and the other is 90919-02230. I don't know which people are using so any body using either of them. Thanks Alan

Hi All Got a Balancer last year when I was in Aussy, some toe rag has been in my workshop and taker a few bits, balancer water pump, gasket set and pr of turbos. Replaced all except the balancer, would cost lots of cash to get another Ross one sent over, looking for a balancer in the UK or the...

Hi All. Wishing you all a Merry Christmas and a very Happy new year, hope Santa brings all the things you asked for Alan

Hi All, I have put up a Spitronic's forum, It's for Ignitions only, mostley for the spitronic and Lexus V8, hope this is ok mods, all welcome to add 2c. http://alanwhitaker.forumchitchat.com/

Hi All, Can you test a valve off the engine. 6 wire one off a 1994 none VVTI engine. Alan

Hi All Just had a inlet flange done, its a cad for a flange not a full machining cad file. I am going to use a 20mm ally plate (just what I have on hand), will have it cut but not the ports, just a small dia port cutout which is included in the drawings, going to get a cad file done just for...

Hi All. Started to wire the engine today, I went with the Spitronic ECU and TCU, I was thinking of loosing the std Ignition and using the LS coils or pencil coils with igniters. Questions Which are the best cops to use or are the LS 1 coils better. I have 6 ignition drivers so can either...

Hi All Now I have the sump almost made I need to know if the sump needs to be bolted to the bell housing for block strength if so anybody got a spare bell housing in the UK I could borrow to fab up the sump mounts. Alan

Hi All, Don't know where I saw it but there was a cad file of the top flange for a 1UZ-FE flange, I am talking about the split from the lower an upper manifold (the one you would bolt a supercharger to) Many Thanks Alan

Hi All. Is the speed sensor on a 1994 LS400 transmission , Hall Effect 3 wire or Magnetic 2 wire, Not able to go to the workshop due to working away but need to order some bits. Alan