Search results

  1. 3

    Wanted WANTED: Crown (etc) Air Flow Meter. 22204-42010

    Chasing a 1989 Crown Air Flow Meter, part number 22204-42010. Preferably in Australia. The same part was also used on other Toyota cars around the 1990's. Anyone got one they can spare, or maybe surplus to your needs? Thanks all.
  2. 3

    1989 Crown Air Flow Meter issue?

    HI guys. Hope all is getting better in whatever neck of the woods you are from! My 1UZ (powering the Chev hot rod) has developed a problem. I am completing the wiring, using the Crown loom and eliminating parts I dont need. But the engine, ECU, ECT etc wiring is absolutely stock. I work on the...
  3. 3

    USZ131 Crown interior diagnostic pinouts?

    Hi All. Like it says, does anyone have the pinout for the interior diagnostic connector in a 1989 crown? I specifically need to know the function of the blue with a yellow stripe wire. It seems to be the +12Volt battery wire but the voltages I see on it indicate its not, or it is modified in...
  4. 3

    Diagnosing a possibly dead 1989 Crown 1UZ ECU

    Hi All. Its been a while! I am trying to diagnose a possibly dead ECU from a 1989 Crown (part number 89661-30430, 8 - 26 - 16 - 22 pin). I can see 12Volts on pins 1 and 2 of the 22 pin connector and ground on pin 14 of the 26 pin connector. I am referring to a set of diagrams I downloaded from...
  5. 3

    1998 Crown fuel sender specs.

    hi all. As it says, I am searching for the specs for a 1998 Crown fuel sender , [1uz engine) Ie full and empty resistance. I have tried the search, and google. lots of misleads. Thanks in advance.
  6. 3

    1UZ left hand coil relocation.

    Hi All. I am tidying up the front of the 1UZ. I want to move the wires that go to the crank angle sensor from where they currently go, across the left hand cam belt lower cover etc, to under the left hand spark plug lead cover, and down the engine side. I intend to run the wires over the...
  7. 3

    Wanted WTB 1989 Crown auto gearbox mount.

    Hi All. Just need a 1989 Crown gearbox mount. The rubber has come off the metal on mine. Anybody have one surplus, or know if there is an alternative? Cheers. Jeff.
  8. 3

    1989 Crown Royal wiring?

    Hiya all: Yes, I know - very old engine/topic/etc. I have a complete Crown Royal saloon 1/2 cut. By that I mean it is (was) complete from the front bumper to where it was cut at about the front seat level. All harnesses, all dash instruments, and it all works fine. (Starts, runs, I can select...
  9. 3

    Trade Crown fan bearing hub assy for swap

    I have a Crown 1UZ fan hub bearing assembly. Great to replace the hydraulic fan motor when yuo are getting rid of excesss ancillaries. I understand I want a hydraulic fan motor assembly to replace mine. Call me, Aus 0412105608. Jeff
  10. 3

    Parts 1UZ Fan hub mounting plate (Crown)

    I have a Crown 1UZ fan hub bearing and front plate (the viscous clutch type). I want to swap for a hydraulic version. (Apparently they are easier to modify). Jeff. 0412105608, Canberra AUS.
  11. 3

    Crown 1UZ fan removal.

    YEs, I know it's been done, but the search keeps on bringing up blank threads (old??). Anyway, I want to remove the fan hub from my 1UZ that was in a Crown, so it has/had the viscous coupling fan. I have taken off the mounting plate, but apart from cutting the whole thing in 1/2, how do I remove...
  12. 3

    Wanted wtd info re mounts

    Hi All: Mounting a 1UZ (ex Crown) into a Chev. Mounts are a little too far back, is there mounts that mount a bit further forward? Cheers
  13. 3

    Dismantling a 1989 Crown

    Hi All: I am dismantling a 1989 Crown and learning a lot about these cars as I go! When I started,I noticed a hydraulic pump in the right hand guard, and noticed that the various hoses seem to go to the suspension units. So, I thought... Hydraulic suspension. Fair enough. Upon further...
  14. 3

    1989 Crown Royal 1/2 cut wont start.

    This should be an easy one... My Crown 1/2 cut wont start. Has spark at the plugs. Cranks OK. I think it's fuel related as I have rigged up a temporary pump which may not be giving enough pressure. I can get fuel from the fuel rails by loosening the cold-start fuel line. Does the cold start...
  15. 3

    Un-tiliting a Crown 1UZ.

    Greetings all, from Oz. I am installing a 1UZ from a Crown in a Street rod. The engine when in the Crown is tilted over to allow space for the steering box. I wish to install it "upright". Obviously this will mean the gearbox is tilted - not an ideal situation (I think). I see from a previous...


Top