Search results

  1. R

    Wiring auto to wolf ECU

    I know wiring autos to aftermarket ECU isn’t a common thing and not many have any experience with these as yet, but I have a couple of questions someone might be able to shed some light on. I worked out the Pinouts from a map I managed to find and it has an input/ output Setup for an OD wire...
  2. R

    89 Crown o2 sensors

    Looking for advice or thoughts on O2 sensors and what alternatives I should consider. I am currently wiring up a tuner series wolf ecu building a new harness and had planned on using wide band sensors, yes Gloverman I am paying attention and yes, I should have bought a Link. I just can’t get...
  3. R

    crown auto to wolf tuner EMS

    Hi Guys Has anyone wired up a crown A341 auto to a wolf tuner or V550 ecu. I am just no sure how many input/outputs it uses as there is no documentation auto transmission hook up. From what I have found from reading various A340/1 posts on the web, it only uses sol1 and 2, lockup, a speed...
  4. R

    Larger Injectors on NA Crown 1Uzfe with aftermarket ecu

    I have an NA early crown running factory auto, and has the small light blue injectors fitted, it doesn't have much in the way of mods at this stage apart from larger exhaust. The motor has been sitting for some time so the injectors will need doing so was wondering which way to go as there is...
  5. R

    What is the latest on COPS conversions for early 1UZFE

    Just wondering what the latest is on converting early 1uzfe to coil over plug. I have seen a couple of conversion kits on ebay that are for converting them but hard to get any real information on the actual product. The ones I have seen are four wire with pig tails and don't need igniters, for...
  6. R

    crown engine fusebox

    Hi Guys anyone out there who can send me a pic of a Uzs131 crown engine bay fuse box cover, as it has the fuse and relay diagram on top. I had venom do the loom for it quiet a few years ago but I need to down size the fuse box to fit under the dash, but I need to know what is in there that I can...
  7. R

    lokar Shifter

    anyone fitted a cable Lokar shifter to a A340E? I noticed that MV automatics in south oz have cable brackets for a B&M shifter could they be used for the Lokar shifter.
  8. R

    Sludge

    I was just wondering about a build up of sludge that is in the oil filler and PVC valve areas, I guess they are in a baffle as I can't see the cams, is this a common problem? The oil is as clean as and the services where all done according to the service book that was in the glove box of the...
  9. R

    Making a new Y pipe

    I want to build a new Y pipe for my crown motor, but unclear as how an original lexus Y pipe is constructed to give it good flow. I am going to use the original crown headers despite their bad design at this stage, having to move oil filters etc to clear rush headers maybe over kill for the...
  10. R

    Genie/ Pacemaker Headers on Crown 1UZFE

    I am looking at headers for a crown 1UZFE in a hotrod, I have looked at Rush import headers but they interfere with the crown oil filter, I don't want to use a front mount filter as it interferes withe the front cross member. Has any one used the genie or pacemaker headers for the land cruiser...
  11. R

    what angle should the motor be installed at

    I have a crown UZfe and was looking at the sump on the auto trans and is angled up. Should this be square to the ground for the fluid pickup also the drain plug is at the back and you would not be able to drain it unless you drop the back of the box down.
  12. R

    Kick down switch

    Hi is there a kick down switch in the toyota crown can't find it in the wiring Diagrams tho there is one fitted to Lexus LS400's ,that is fitted under the accelerator pedal. Also where is the netural safety switch and gear selector switch located. On the box?
  13. R

    from floor to column shift

    Hi Guys any one set up the crown auto on a column shift, probably going to use 70's chev steering column. not much room on the floor for a floor shift in the hotrod. Just want to see if anyone else has done it, before forking out money. As they are expensive in OZ.


Top