Search results

  1. R

    92 Lexus SC400 Part out...

    Pictures of interior please! Specifically door cards and trim. THanks, Andrew
  2. R

    Kiwi VVti stock car engine

    I just want to get my hands on a non-VVTI carb manifold!!!!
  3. R

    fish bracket

    I have the same question...
  4. R

    Any luck finding the carbureted manifolds?

    I have actually seen the Lynchbuilt website and may decide to contact them. As for the second link, the whole idea is to lose the crappy, factory manifold haha. I won't actually be doing away with the fuel injection. I will most likely use an Edelbrock Competition throttle body set-up.
  5. R

    Any luck finding the carbureted manifolds?

    We conversed back and forth a bit, but nothing definitive. I will be going on a stock port 1st gen 1UZFE. Would have never thought the manifolds would go for around $1,000 USD! Is that the price for new or used? Fabricated or cast?
  6. R

    Any luck finding the carbureted manifolds?

    Thanks, cribbj. I'll try again. I've already contacted both Gloverman and XR8tt in the past. Appreciate the info, Andrew
  7. R

    Any luck finding the carbureted manifolds?

    I keep scouring this site, v-eight.com, the web, eBay, TradeMe.co.nz, racingjunk, etc. I've tried contacting Kelford Cams, CSL Cams, and MarxMotorsports with no responses or info. HELP PLEASE!!! Thanks, Andrew Spring, TX 281-543-695one
  8. R

    Lextreme hacked?

    I had the same problem. Used "forums" insteand of "forum" and it's all good. Weird...
  9. R

    building a N/A 1uz and need advice

    I had started a couple threads years ago asking about 4.7 block with 4.0 heads. Are you using the 4.7 block and heads?
  10. R

    Tundra 5.7 3URFE Parts/Block

    Bought a Tundra back in 2009 and had the TRD supercharger installed at the same time. Sold the truck a year ago and am now cleaning out my garage full of parts. These parts have been sitting in boxes since November of 2009 with maybe 100 miles on them. SILVER Engine Cover - $60 Intake...
  11. R

    Tundra 5.7 3URFE Parts

    Just noticed this is in the wrong section :/
  12. R

    Tundra 5.7 3URFE Parts

    Bought a Tundra back in 2009 and had the TRD supercharger installed at the same time. Sold the truck a year ago and am now cleaning out my garage full of parts. These parts have been sitting in boxes since November of 2009 with maybe 100 miles on them. SILVER Engine Cover - $60 Intake...
  13. R

    Calculating 1/2UZ Compression Ratio

    Getting back into this little project... Anyone have more to offer as far as more recent/updated info, experience, etc.? Thanks, Andrew
  14. R

    3URFE short block/block

    Looking for a 3URFE short block or just a bare block. LMK! Thanks, Andrew TEXT @ 281-543-695one
  15. R

    N/a 1uz

    Not worth it. If you haven't done any porting yourself, don't do it. If you don't have the money to pay someone to do it, don't do it yourself haha. Remember that if you over port or mess up, there are no re-dos. The intake side of the heads are fine for NA power. It is the manifold that...
  16. R

    N/a 1uz

    No REAL need to port match anything. BFI Headers 2.5" Exhaust(make sure it is an x-pipe or y-pipe design) Cams will probably be from Kelford or Lextreme. Just make sure you check the valve to cam clearance and adjust accordingly. I was interested in a MAP-ECU piggyback. That way you can...
  17. R

    Have complete front sump to swap or buy rear sum (AUS)

    I have a rear sump(Soarer) I'm willing trade, but I'm in the US. So shipping might not be worth while.
Top