Search results

  1. M

    injector seal kit

    yes, or you may find them on amazon or ebay
  2. M

    1UZ into MB 190E

    re fitting goodies into MBs here are some ideas to ponder;
  3. M

    Long shot, but B/W / Tremec T5 question?????

    kinda an aside and off topic, but back in the ice age I had a Rover V8 bent into a Austin H - fantastic wow, what a car and eye (ear) turner
  4. M

    Problems With Exhaust Size

    hehe, or engine/boats a related question, with my 4 pipes, 2 pipes each side/bank I paired the following cylinders into 1 pipe the cylinder that fires first + the penultimate firing cylinder and the cylinder that fires as number 2 + the cylinder that fires last does that sound about right?
  5. M

    Problems With Exhaust Size

    thats a personality defect of mine, opting for overkill solutions yep, eagerly awaiting Mr Cribb
  6. M

    1uzfe knocking

    sure does, looks like a pretty good kit that - and hopefully thoroughly tested
  7. M

    Problems With Exhaust Size

    I take it that this means that you lose the pump/suction effect in the pipes if they are too large. I have 4 pipes (2 cylinders/pipe) start with a small piece of 2 inch then 2.5 inch then finally 3 inch. Do you have to maintain the "smaller size" all the way to the end in order not to loose...
  8. M

    1uzfe knocking

    no, I am afraid not they are handmade by a gasket maker shop in Bangkok
  9. M

    1uzfe knocking

    interesting, I am paying about 40 australien for 2 cylinder head gaskets
  10. M

    Ideas/tips for newbie

    trust you but improving fuel injection and ignition - maybe slightly increase compression ratio - at least polishing air intake as much you can how much could you get out of that?
  11. M

    Where are you located?

    Hoe gaan dit u would need a 1uz to climb table mountain
  12. M

    Thoughts on this Manifold design?

    wow, I like that one,
  13. M

    1uz fan idler bracket failure

    right, my man at yeomans in brighton is Bob Ellis, he is the spare part manager very very helpful
  14. M

    Speed sensor #1 issue mystery

    if your electro mechanic sorts it out please be so kind as to come back here and explain problem/solution
  15. M

    1uz fan idler bracket failure

    by all means do, was not suggesting that you divert your order just informing you that there are OK Toyota dealers on the foggy islands btw, I also purchase from gloverman, works fine
  16. M

    1uz fan idler bracket failure

    Unlucky with your dealer then. I have bought a number of 1UZ parts from the Toyota shop Yeoman's in Brighton. To start with I did not know year, did not know car, did not know engine generation, no problem. Shop has always been very very helpful. All sorted by email from Thailand. When parts...
  17. M

    High Spec 1uz fe in race MGB GT Project

    talkin' about old world UK sports cars; here is something to ponder; and and
  18. M

    High Spec 1uz fe in race MGB GT Project

    Tom B I like what you're doing! Once upon a time in the previous century I bent a Rover V8 into an Austin Healey, what a party! 1UZ into a Morris Garages would be just great!
  19. M

    Grounding 1UZ ECU casing in a fibreglass car

    mine likewise, not grp but acryl plastic box, no separate grounding
  20. M

    1UZ in Thai longtail boat

    RUNS! Put the rest of the mill together yesterday, manifolds - exhaust pipes - radiator - fans - emergency cooling stuff - coolant And surpirse surprise, it ran smoothly on all 8. Radiator fans starting and stopping as they should. Oil cooler fans OK. Will check again today and tomorrow, if...
Top