REGISTER NOW TO REMOVE ADS FOREVER

Search results

  1. Alan Whitaker

    1UZFE Bottom End

    Hi Zuffen & Cribbj. Never been away look in twice a week, I got some bits from a guy who was on the V8.com but the machining was all over the place to say they were not usable is being kind, I have just finished a rebuild and was going to add a windage tray and scraper to the bottom end. I was...
  2. Alan Whitaker

    1UZFE Bottom End

    I take it that's a no then
  3. Alan Whitaker

    1UZFE Bottom End

    Anybody making stud girdles, windage trays and crank scrapers these days. Thanks Alan
  4. Alan Whitaker

    Double Crank Pulley for supercharger question...?

    Not with stock ones, I have seen someone bolt a pulley to the front of a stock one before
  5. Alan Whitaker

    Double Crank Pulley for supercharger question...?

    I have the Ross balancer, you can just add your drive pulley to it
  6. Alan Whitaker

    Spitronics and Perth

    Perth Australia
  7. Alan Whitaker

    Spitronics and Perth

    Hi All. Is there anybody in Perth running the Spitronics ECU and TCU with turbos. Alan
  8. Alan Whitaker

    Aftermarket Pulley Tensioner

    Thanks , I have a 4 rib pulley on the alternator. looks just what I need. postage would be to the UK Alan
  9. Alan Whitaker

    Aftermarket Pulley Tensioner

    Hi All Are there any serpentine aftermarket pulley tensioners so I can only run the alternator. Alan
  10. Alan Whitaker

    Custom Inlet Manifold

    Ok you will have to go on Facebook and type into your friends search bar 1UZFE V8 BUILDS & PARTS BUY/SELL/SWAP it should come Alan
  11. Alan Whitaker

    Custom Inlet Manifold

    Hi This is an example of the work they do. There is a thread re making a 1UZFE one. Alan
  12. Alan Whitaker

    Custom Inlet Manifold

    Hi Link may not work It's in the 1UZFE V8 BUILDS & PARTS BUY/SELL/SWAP Alan
  13. Alan Whitaker

    Custom Inlet Manifold

    Hi All This is on Facebook https://www.facebook.com/photo.php?fbid=10156146929735403&set=pcb.628612827241481&type=3&theater
  14. Alan Whitaker

    A650 shift kit, is it worth it?

    Thanks George. Might just fit the kit and leave the holes. have a good transmission cooler as well. Alan
  15. Alan Whitaker

    A650 shift kit, is it worth it?

    Hi All Just to bump this. Anybody done this as yet, just wanting to know if it's a good mod or not?. Have the kit on the bench and the box ready to fit to the engine. Thanks for any input Alan
  16. Alan Whitaker

    What to do with your old cam belt

    Hi George It's a strap wrench, works like a oil filter wrench. You can take the cam bolt out of a cam out of the engine on your bench with no need to hold the cam it's self Alan
  17. Alan Whitaker

    A650 shift kit, is it worth it?

    Hi George was going to do mine if your install went ok, not sure about drilling the hole. is it in the casket or the valve body, a bit uncertain on this. Alan
  18. Alan Whitaker

    35 50LS gearbox

    Many Thanks for that, don't know if these transmissions are good for 500 hp or do they need any special parts. been looking at a upgrade but most bits are listed for the 340 , been looking at ATFspeed.com and IPT transmissions. Alan
  19. Alan Whitaker

    35 50LS gearbox

    Hi All As there is no edit on posts It's a 35 50 LS The guy says its from a GS430 but not sure about this, help anybody Alan
  20. Alan Whitaker

    35 50LS gearbox

    Hi All Just got a box, was sold as a A650E 5 speed, the name plate says 30 50 LS, I think both are 5 speed. Question what are these out of and how strong are they, going on the back of a 1UZ-FE none VVTi (1994) engine, is the torque converter any better then a 340 Alan
Top