Recent content by Yotarip

  1. Y

    1UZ vvti into a 4x4 1996 4Runner

    Did you supply 12 volts to the +BM terminal on the ecu? That powers the throttlebody.
  2. Y

    2UZ Throttle body on 1UZ VVTi

    The 2uz non vvti and 1uz vvti throttle bodies are identical. They are both cable actuated electric throttle bodies.
  3. Y

    1UZ cooling system questions / issues

    My experience. My LS400 started slightly overheating when sitting in traffic and progressively got worse. Eventually the heater stopped blowing cold. I didn't loose any coolant or have any compression issue so I knew it couldn't be the head gasket. I pulled one heater hose while the motor was...
  4. Y

    1uz swap, bad ecu?

    E1 is ground. Check for continuity across E1 and the engine block first. The all ecu harness to engine grounds must be mounted.
  5. Y

    sc400 X-pipe and stock mufflers

    I'm running a 3uz in my 90 supra. My exhaust is 2.5" pipe with an x-pipe right after the trans. Then it transitions to a y-pipe just before the differential and a single pipe up to the 2.5" free flowing magnaflow muffler. Sounds really good but just a little raspy around 5k rpm. Might install...
  6. Y

    Sc400 vvti swap wiring help

    I'd suggest you go here to ebay and buy the factory wiring manual. http://www.ebay.com/itm/SHOP-MANUAL-LEXUS-SC400-SC300-ELECTRICAL-WIRING-DIAGRAM-1998-SCHEMATIC-SC-400-/221596545442?fits=Model%3ASC400&hash=item33982ef1a2:g:VO8AAOxyBLBR8i1x&vxp=mtr I have GS400 and LS400 vvti motors and...
  7. Y

    The Engineered 1UZ V8 Datsun 620 Build

    Dude. You make me ashamed to post my 1uz builds. :(
  8. Y

    Non immobilized 1UZ VVTi, 3UZ ECUs

    Thanks for the information. Looks like I'll be changing out the knock sensor once I get closer to finishing. Might as well buy them new.
  9. Y

    Non immobilized 1UZ VVTi, 3UZ ECUs

    Yeah. I actually sent you a 3uz ecu to exchange for the bypassed 1uz ecu. I chose the 1uz ecu for two reasons. 1. The 3uz ecu would require me to install the electronic accelerator pedal in my car. I'm not a small guy and I hate squeezing myself under the dash. 2.The ls400 1uz vvti harness...
  10. Y

    Non immobilized 1UZ VVTi, 3UZ ECUs

    Hello George, You have another happy customer in the USA. I just got my UZ VVti motor running with your modified ecu. She started on the first try after I realized the throttle body needed 12 volts. https://youtu.be/-VAl1d55i1M I read one of the threads here where you helped a member out with...
  11. Y

    Non immobilized 1UZ VVTi, 3UZ ECUs

    Thanks!! BTW, I have another ecu I want to exchange for one of your bypassed ecu's. It's from a 1999 LS400 VVti. I'll send you an email in a few days. Thanks again.
  12. Y

    Non immobilized 1UZ VVTi, 3UZ ECUs

    George, I have an immobilser bypassed ecu I bought from you earlier this year. I'm close to start wiring it up but I'd like to know which wires , if any , I need to wire up on the grey plug that would originally power the key reader accessories. Thanks.
  13. Y

    1uz vvti into a Volga

    She sounds GREAT! I wish the laws here would allow me to do something similar. The police would ticket me everytime I drove it. We can't legally change the path of our exhaust from it's original design. My exhaust doesn't sound like a V8 to most people. Some have said it sounds like a huge...
  14. Y

    1uz vvti into a Volga

    LOL. You and I both know those welds suck but I'm learning. They aren't pretty but welding myself saves me a ton of money on my swaps/ projects. Here's a sound clip. https://youtu.be/fUsFG4jEYJE
  15. Y

    1uz vvti into a Volga

    I did something similar on my 1992 toyota cressida. 2.25" pipe with x-pipe, two glasspacks and to dual in single out muffler. Sounds great!
Top