Search results

  1. 1

    Project Thread 3.3ltr whipple into Ls400

    How did you go with the power runs?
  2. 1

    M112 Pulleys

    Rod, I know it has been a few years, but I would like to see that photo...
  3. 1

    M112 Supercharger Fitment

    Dave have you tested the flow balance of the system? Without a calibrated restriction at each point of discharge there will probably be significant variation.
  4. 1

    Where to buy loom plugs

    http://www.alanco.com.au/
  5. 1

    Water/Alcohol Injection.

    It came from Aquamist, however they are a standard SMC fitting, so should be available locally.
  6. 1

    Water/Alcohol Injection.

    http://home.swiftdsl.com.au/~indecent/Jasper%20Stewart's%20Thesis.pdf
  7. 1

    Water/Alcohol Injection.

    I am having trouble getting an FTP connection to host it, and it's too big to post as an attachment. If you give me an email address I'll send it to you.
  8. 1

    Water/Alcohol Injection.

    Yes, last year. I ended up spending about $3k on nitrous oxide on top of my hardware costs!
  9. 1

    Water/Alcohol Injection.

    Some pics of my setup here: http://lextreme.com/forums/showthread.php?t=6338&highlight=water+injection
  10. 1

    Supra MKIII

    I agree with John. The frame rails in the MK3 are alot closer together than in the MK4, and there is not much room in there for exhaust manifolds.
  11. 1

    Seller Feedback Dellow

    This is true. My Dellow flywheel was tapped with UNC threads, including the shallow holes which should have been for dowels. When I called them to ask about it, they didn't really want to know and suggested I could send it back across the country for them to "have a look at". Although it...
  12. 1

    supercharger intercooler manifold problem.

    10 characters
  13. 1

    New Turbo 4.5L V8 Diesel, in Aus Toyota Cruiser

    The company I work for has bought one of these, and I took it for a drive today. Much better than the 1HZ diesel it replaces! It actually spins the wheels a bit when you take off quickly :saevil: I managed to surprise a few people who thought it was just another sluggish oil burner...
  14. 1

    supercharger intercooler manifold problem.

    Cribbj, Do you have any more info or links to do with that SC setup? I have searched a bit for stuff that Reg has done, but come up with nada... Also, anyone know what the galleries in the the lower intake between the injector pairs are for?
  15. 1

    supercharger intercooler manifold problem.

    There is no fundamental difference in flow behavior between an NA engine operating at 101kPa manifold absolute pressure, and an FI engine operating at say 150kPa manifold absolute pressure. At higher rpm both are subject to induced pressure waves in the intake tracts, which can correspond with...
  16. 1

    1uz->R154 Best options??

    It is the clutch cover that came with the dellow kit, but my local clutch guy in Perth modified it by changing the location of the pivot points to give it a higher clamp load. The ceramic friction plate was reused from my old turbo 7M clutch setup.
  17. 1

    supercharger intercooler manifold problem.

    How is this any different to an NA engine with atmospheric pressure in the plenum?
  18. 1

    1uz->R154 Best options??

    The clutch has held up OK to some big nitrous hits so far. It has a very aggressive friction material and a fairly high clamp load.
  19. 1

    1uz->R154 Best options??

    It's a GT4202R. The coils are MSD, I forget the part number, but I'll bet it's on their website somewhere. If I was going to do it again, I'd use Bosch coils, the MSD ones are an awkward shape to fit into the available space.
  20. 1

    1uz->R154 Best options??

    http://lextreme.com/forums/showpost.php?p=62551&postcount=38


Top